MULTIQUIP MC12PH Скачать руководство пользователя

Страница: 10 / 79

MC12PH CONCRETE MIXER • OPERATION AND PARTS MANUAL — REV. #1 (09/02/15) — PAGE 9

SAFETY INFORMATION

FUEL SAFETY (GASOLINE MODELS ONLY)

DANGER

DO NOT

start the engine near spilled fuel or combustible

fl uids. Fuel is extremely fl ammable and its vapors can

cause an explosion if ignited.

ALWAYS

refuel in a well-ventilated area, away from

sparks and open fl ames.

ALWAYS

use extreme caution when working with

fl ammable

liquids.

DO NOT

fi ll the fuel tank while the engine is running

or hot.

DO NOT

overfi ll tank, since spilled fuel could ignite if it

comes into contact with hot engine parts or sparks from

the ignition system.

Store fuel in appropriate containers, in well-ventilated

areas and away from sparks and fl ames.

NEVER

use fuel as a cleaning agent.

DO NOT

smoke around or near the

equipment. Fire or explosion could result

from fuel vapors or if fuel is spilled on a

hot engine.

GENERATOR SAFETY

If using a generator to power mixer, refer to

applicable generator manual safety information

section.

ELECTRIC MOTOR SAFETY

(ELECTRIC MODELS ONLY)

NOTICE

Operate electric motor only at the specifi ed voltage

indicated on the nameplate.

DO NOT

spray water onto electric motor.

ALWAYS

disconnect AC power plug from power source

before moving mixer.

ALWAYS

make sure the ON/OFF switch

on the electric motor is in the OFF position

when not in use and before inserting the

mixer’s power plug into an AC receptacle.

Power Cord/Cable Safety

DANGER

NEVER

let power cords or cables

lay in water.

NEVER

use

damaged

worn

cables or cords when

connecting equipment to generator. Inspect for cuts in

the insulation.

NEVER

grab or touch a live power

cord or cable with wet hands. The

possibility exists of

electrical shock,

electrocution or death.

Make sure power cables are securely connected.

Incorrect connections may cause electrical shock and

damage to the mixer.

CAUTION

Ensure that cables and cords will not be tripped over or

trapped underneath the mixer.

NOTICE

ALWAYS

make certain that proper power or extension

cord has been selected for the job.

TRANSPORTING SAFETY

CAUTION

NEVER

allow any person or animal to stand underneath

the equipment while lifting.

NOTICE

ALWAYS

make sure forklift forks are inserted into pockets

(if applicable) as far as possible when lifting the mixer.

ALWAYS

shutdown engine before transporting.

NEVER

lift the equipment while the engine is running.

Tighten fuel tank cap securely and close fuel cock to

prevent fuel from spilling.

DO NOT

lift machine to unnecessary heights.

ALWAYS

tie down equipment during transport by

securing the equipment with rope.

NEVER

tip the engine to extreme angles during lifting as

it may cause oil to gravitate into the cylinder head, making

the engine start diffi cult.

Discount-Equipment.com

Содержание MC12PH
















































































Результаты поиска

Содержание MC12PH

Отзывы:

Похожие инструкции для MC12PH

Бренды по названию

Популярные бренды

MULTIQUIP MC12PH, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MC12PH

Отзывы:

Похожие инструкции для MC12PH

Бренды по названию

Популярные бренды