MULTIQUIP JH55C страница 39 Скачать руководство пользователя

Страница: 39 / 104

JH55C WALK-BEHIND TROWEL • OPERATION AND PARTS MANUAL — REV. #2 (9/4/15) — PAGE 39

MAINTENANCE

TROWEL ARM LEVER ADJUSTMENT

The easiest and most consistent way to adjust the trowel

arm lever is to use the Trowel Arm Adjustment Fixture

(P.N. 1817).
As each trowel arm is locked into the fixture, the arm bolt

is adjusted to where it contacts a stop on the fixture. This

will consistently adjust all of the trowel arms, keeping the

finisher as flat and evenly pitched as possible.
This fixture will allow consistent adjustment of the trowel

arm lever. It comes with all the hardware necessary to

properly accomplish this maintenance and instructions on

how to properly utilize this tool. Adjusting the trowel arm

lever without a fixture requires a special talent.
Perform the following procedure when adjusting the trowel

arm lever:
1. Unscrew the locking bolts on the adjustment fixture and

place the trowel arm (lever attached) into the fixture

channel as shown in Figure 60.

2. Ensure the fixture arm is in the up position.
3. A thin shim may be required to cover the blade holes on

the trowel arm. Make sure to align the trowel adjustment

bolt with the fixture adjustment bolt.

Figure 60. Trowel Arm Adjustment Fixture

4. Use an allen wrench to tighten the locking bolts

securing the trowel arm in place.

5. Adjust the bolt distance shown in Figure 60 to match

one of the arms. The other arms will be adjusted to

match this distance.

6. Loosen the locking nut on the trowel arm lever, then

turn the trowel arm adjusting bolt until it barely touches

(.010") the fixture adjusting bolt.

ARM

SHIM

LOCKING

BOLTS

TROWEL ARM

ADJUSTMENT FIXTURE

TROWEL

ARM

LEVER

FIXTURE

ARM

DISTANCE

.010 INCH

ADJUSTMENT

BOLT

ADJUSTMENT

BOLT

7. Once the correct adjustment is made, tighten the lock

nut on the trowel arm to lock in place.

8. Loosen locking nuts on the adjustment fixture, and

remove trowel arm.

9. Repeat steps for the remaining trowel arms.

REASSEMBLY

1. Clean and examine the upper/lower wear plates and

thrust collar. Examine the entire spider assembly. Wire

brush any concrete or rust buildup. If any of the spider

components are found to be damaged or out of round,

replace them.

2. Make sure that the bronze trowel arm bushing is not

damage or out of round. Clean the bushing if necessary.

If the bronze bushing is damaged or worn, replace it.

3.  Reinstall bronze bushing onto trowel arm.
4.  Repeat steps 2 -3 for each trowel arm.
5.  Make sure that the spring tensioner is in the correct

position to exert tension on the trowel arm.

6. Insert all trowel arms with levers into spider plate (with

bronze bushing already installed) using care to align

grease hole on bronze bushing with grease hole fitting

on spider plate.

7. Lock trowel arms in place by tightening the hex head

bolt with zerk grease fitting and jam nut.

8.  Reinstall the blades onto the trowel arms.
9.  Install stabilizer ring onto spider assembly.
10.  Reinstall lower wear plate, thrust collar and upper wear

ring in the reverse order that they were disassembled

onto the spider shaft. Make sure that there is little or

no lateral movement between the thrust collar and the

spider shaft.

11. Carefully lift the upper trowel assembly, line up the

keyway on gear box main shaft and insert into spider

assembly.

12. Reinstall square head cone point into spider plate and

tighten in place. Tighten jam nut. Use care in making

sure point of set screw engages groove in gear box

main shaft.

Содержание JH55C









































































































Результаты поиска

Содержание JH55C

Отзывы:

Похожие инструкции для JH55C

Бренды по названию

Популярные бренды

MULTIQUIP JH55C, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание JH55C

Отзывы:

Похожие инструкции для JH55C

Бренды по названию

Популярные бренды