MULTIQUIP JH55C Скачать руководство пользователя

Страница: 8 / 104

PAGE 8 — JH55C WALK-BEHIND TROWEL • OPERATION AND PARTS MANUAL — REV. #2 (9/4/15)

SAFETY INFORMATION

Do not operate or service the equipment before reading

the entire manual. Safety precautions should be followed

at all times when operating this equipment.

Failure to read and understand the safety

messages and operating instructions could

result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you

about potential hazards that could injure you or others. The

safety messages specifically address the level of exposure

to the operator and are preceded by one of four words:

DANGER, WARNING, CAUTION

NOTICE.

SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided,

WILL

result in

DEATH

SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided,

COULD

result in

DEATH

SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided,

COULD

result in

MINOR

MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazard associated with the operation of this

equipment will be referenced with

hazard symbols

which

may appear throughout this manual in conjunction with

safety messages.

Warning decals

associated with the operation of this

equipment are defined below:

Inhaling exhaust fumes can result in severe
injury or death.
Only operate equipment in well ventilated areas.

inhale exhaust gases/fumes.

DO NOT

WARNING

Lethal Exhaust Gas Hazard

HOT PARTS

can burn skin.

CAUTION

Burn Hazard

touch hot parts. Allow machine a sufficient

amount of time to cool before performing maintenance.

DO NOT

Gasoline fuel can cause fire or explosion. Stop
engine before refueling.
Keep cigarettes, sparks and flames away from hot
surfaces.

WARNING

Explosive Fuel Hazard

SYMBOL

SAFETY HAZARD

Keep hands and feet clear of guard rings.
Stop engine before servicing.

WARNING

Rotating Blade Hazard

To avoid injury you must read and
understand operator’s manual before
using this machine.

P/N 23700

allow any person

to stand underneath the trowel while lifting.

NEVER

P/N 36099

ALWAYS

wear protective clothing when

operating this equipment

This machine to be operated by qualified
personnel. Ask for training as needed.

Lifting Crush Hazard

lift trowel with pans attached.

DO NOT

WARNING

Read Manual

NEVER

operate this equipment with guards

removed. Keep hands clear.

WARNING

Training

Guard Hazard

WARNING

make sure handle is securely attached.

On Quick Pitch™ models make sure T-Handle
latch is locked (engaged).

ALWAYS

DECAL

SAFETY HAZARD

Содержание JH55C









































































































Результаты поиска

Содержание JH55C

Отзывы:

Похожие инструкции для JH55C

Бренды по названию

Популярные бренды

MULTIQUIP JH55C, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание JH55C

Отзывы:

Похожие инструкции для JH55C

Бренды по названию

Популярные бренды