Exclusive U.S. Distributor
19
20
20
19
If the DMX value of channel 3 is 050-255, channel 1 selects fade/switch colors, see
table below. Channel 3 controls the fade/switch speed (050=slow/255=fast). Channel 4
strobe speed is 015=slow (1Hz) to 255=fast (18Hz).
“CBAL” Color Balance Mode
In this mode you can define the unit’s color balance by setting a maximum brightness for
each LED color, giving you the individual color balance you desire. Any changes made
to the color balance will affect the unit in all modes. Press the MODE button (1) until the
display shows “CBAL”. Once color balance mode is entered all the LEDs will turn on at
their set value. Use the left/right buttons (2 or 3) to enter color balance mode and cycle
though “R###”, “G###”, and “B###”. ### indicates values from 200 through 255. (Values
below 200 are disabled to avoid overall output reduction of the fixture.) Pressing the +/-
buttons (4 or 5) will change the values. All changes are effective immediately.
NOTE:
To make sure that several fixtures used together do not exhibit different color
behavior, all fixtures must be calibrated to the same color balance.
DMX channel
Value Range
Function
1
000-015
Fade Red - Green
016-031
Fade Blue - Green
032-047
Fade Blue - Red
048-063
Fade Red - Lime
064-079
Fade Hot Pink - Lime
080-095
Fade Pink - Blue
096-111
Fade Turquoise - Pink
112-127
Fade Red - Green - Blue (All Colors)
128-143
Switch Red - Green
144-159
Switch Green - Blue
160-175
Switch Red - Blue
176-191
Switch Red - Yellow
192-207
Switch Hot Pink - Lime
208-223
Switch Pink - Blue
224-239
Switch Turquoise - Pink
240-255
Switch Red - Green - Blue
2
000-255
Intensity
3
050-255
Fade/Switch Speed
4
000-014
Strobe off
015-255
Strobe on
“EDIT” Edit Settings Mode
Press the MODE button (1) until the display shows “EDIT”. Pressing the left/right buttons
(2 or 3) will cycle through the following options.
“ADMX” Automatic DMX Addressing –
Automatic DMX Addressing is used
to quickly setup multiple Multiform HP5-70 units that are daisy chained with DMX
cable. Two modes, Slave and DMX, are available. When in DMX mode, the first unit
will determine the DMX mode and addresses of the units. The desired DMX mode and
starting address needs to be set on the first unit prior to using this feature.
Press the left/right buttons (2 or 3) until the display shows “ADMX”. Pressing the
+/- buttons (4 or 5) once shows “ OFF”. Pressing the + button (4) will set the units to
“GDMX” (General DMX mode) and start the auto addressing process. This process
assumes that it is executed from the first device in a chain. It will set all the following
devices’ settings to the same DMX mode as the first unit and assign DMX channels
consecutively according to the chosen DMX mode. Pressing the - button (5) will set the
units to DMX Slave Mode. The master unit will be assigned to slave group 1, and the
following units will be assigned to consecutive groups up to “SLA4” then starting over at
“SLA1”, i.e. Unit 2 = “SLA2”, unit 3 = “SLA3”, unit 4 = “SLA4”, unit 5 = “SLA1”, and so on.
NOTE:
For this to execute properly, the first unit must not be connected to DMX and all
units need to be in one of the following operating modes when the process is initiated –
DMX Slave Mode, General DMX Mode, Color Balance Mode, or Edit Settings Mode.
“ALOK” Auto Lock –
Press the left/right buttons (2 or 3) until the display shows
“ALOK”. Press the +/- buttons (4 or 5) to alternate between “ ON” or “ OFF”. When turned
on, the unit will lock itself after 1 minute with no button presses. To unlock a locked unit,
press the left (2) and right (3) buttons simultaneously.
“ADIS” Auto Display Off –
Press the left/right buttons (2 or 3) until the display
shows “ADIS”. Press the +/- buttons (4 or 5) to alternate between “ ON” or “ OFF”. When
turned on, the display backlight will turn off after 1 minute with no button presses.
Pressing any button will turn the display backlight on again. The display elements
themselves remain active at all times. When turned off, the display backlight stays lit.
“TEMP” Temperature Display –
Press the left/right buttons (2 or 3) until the display
shows “TEMP”. Press the +/- buttons (4 or 5) to alternate between “ ON” or “ OFF”.
When turned on, the display will show the current operating temperature in °C after 1
minute with no button presses. Pressing any button will return the display to normal
operation.
