Exclusive U.S. Distributor
17
17
18
18
“FP” Fade Patterns Mode
In this mode you will only find soft fade patterns. Press the MODE button (1) until the
first two digits on the display shows “FP”. Choose a pattern, “FP 0” – “FP 7”, by pressing
the left/right buttons (2 or 3), see table below.
The +/- buttons (4 or 5) change the color fade speed, “SL 0” – “SL25”. Pressing the
+/- buttons (4 or 5) once shows the current setting. The setting can then be changed
by using the +/- buttons (4 or 5), see table below. The display will automatically return
to show “FP##” after 5 seconds, and the speed setting will remain as set.
NOTE:
This mode is automatically disabled when an external DMX signal is present.
#
Pattern
#
Pattern
FP 0
Red - Green
FP 4
Hot Pink - Lime
FP 1
Green - Blue
FP 5
Pink - Blue
FP 2
Blue - Red
FP 6
Turquoise - Pink
FP 3
Red - Yellow
FP 7
Red - Green - Blue (All Colors)
Setting
Speed
Setting
Speed
SL 0
1 loop per 960 seconds
SL13
1 loop per 3 seconds
SL 1
1 loop per 480 seconds
SL14
1 loop per 2 seconds
SL 2
1 loop per 360 seconds
SL15
1 loop per 1.5 seconds
SL 3
1 loop per 240 seconds
SL16
1 loop per 1.25 seconds
SL 4
1 loop per 120 seconds
SL17
1 loop per 1 second
SL 5
1 loop per 80 seconds
SL18
1.2 loops per second
SL 6
1 loop per 40 seconds
SL19
1.4 loops per second
SL 7
1 loop per 20 seconds
SL20
1.6 loops per second
SL 8
1 loop per 12 seconds
SL21
1.9 loops per second
SL 9
1 loop per 10 seconds
SL22
2.2 loops per second
SL10
1 loop per 8 seconds
SL23
2.5 loops per second
SL11
1 loop per 6 seconds
SL24
2.8 loops per second
SL12
1 loop per 4 seconds
SL25
3.2 loops per second
“SLA” DMX Slave Mode
The Slave mode offers 4 independent groups of slaves. Press the MODE button (1) until
the first three digits on the display shows “SLA”. The +/- buttons (4 or 5) change the slave
group, “SLA1” – “SLA4”. The first unit will then control any connected units. Each slave
group will be in the same preset and speed as the master, but the timing of the preset
will be offset from the previous slave group. To have all units operating together, set all
units to slave group 1.
DMX
channel
Value
Range
Function
DMX
channel
Value
Range
Function
1
000-010
Red
1
154-163
Light Purple
011-020
Green
164-174
Light Lavender
021-030
Blue
175-184
Light Blue
031-040
Yellow
185-194
White 1 (cool)
041-051
Pink
195-204
White 2
052-061
Turquoise
205-215
White 3
062-071
Lime
216-225
White 4
072-081
Orange
226-235
White 5 (warm)
082-092
Marine
236-245
Light Orange
093-102
Blue Green
246-255
Dark Orange
103-112
Lavender
2
000-255
Intensity
113-122
Hot Pink
3
000-049
Static Colors
123-133
Flesh
4
000-014
Strobe off
134-143
Light Blue Green
015-255
Strobe on
144-153
Light Green
“GDMX” General DMX Mode
Press the MODE button (1) until the display shows “GDMX”. When the unit is receiving a
DMX signal, the DMX indicator (11) will be illuminated.
Setting the DMX Address
The +/- buttons (4 or 5) change the DMX address, “ 1” – “ 512”. Pressing the +/- buttons
(4 or 5) once shows the current DMX address. The DMX address can then be changed
by using the +/- buttons (4 or 5). Holding the +/- buttons (4 or 5) for longer than 1
second accelerates the change rate of the displayed value to 3 times normal speed. The
display will automatically return to show “GDMX” after 5 seconds, and the DMX address
will remain as set. The DMX address remains the same regardless of the selected DMX
control mode. However, the number of channels used may change depending on the
selected DMX control mode.
Selecting a DMX Control Mode
Pressing the left/right buttons (2 or 3) once shows the current DMX control mode. The
left/right buttons (2 or 3) can then be used to cycle through the following DMX control
modes.
-
“3RAW” 3 Channels – 1=Red, 2=Green, 3=Blue
-
“3CCC” 4 Channels – 1=Red, 2=Green, 3=Blue, 4=Intensity/Strobe
-
– CH 4 values – 000-127=Intensity, 128-239=Strobe, 240-255=Full Intensity
-
“3CMS” 5 Channels – 1=Red, 2=Green, 3=Blue, 4=Intensity, 5=Strobe
-
“5RAW” 5 Channels – 1=Red, 2=Green, 3=Blue, 4=Amber, 5=White
-
“5CMS” 7 Channels – 1=Red, 2=Green, 3=Blue, 4=Amber, 5=White,
6=Intensity, 7=Strobe
-
“HSLS” 4 Channels – 1=Hue, 2=Saturation, 3=Lightness, 4=Strobe
-
“PRES” 4 Channels – Presets, see section below.
When the DMX control mode is set to Presets, the DMX value of channel 3 determines
which presets channel 1 controls. If the DMX value of channel 3 is 000-049, channel
1 selects static colors, see table below. Channel 4 strobe speed is 015=slow (1Hz) to
255=fast (18Hz).
