MULTI MEASURING INSTRUMENTS MCL-800D+ Скачать руководство пользователя страница 3

Страница: 3 / 16

WARNING

To prevent electric shock.

• For safety reasons, use the instrument under a low-voltage circuit of

AC600V or less.
Check the circuit voltage before measurement.

• Do not clamp any bare wire.
• Do not measure when the CT or the body is damaged nor the battery

cover is removed.

• Do not operate with wet hands, including when battery replacement.

Also do not use in extremely humid places or when the instrument body
is wet as well.

• Do not disassemble or modify the instrument.

CAUTION

• Wipe the instrument gently with a soft cloth moistened with a small

amount of water or neutral detergent, when it gets dirty. Do not use any
abrasives or organic solvents.

• Do not use or leave the instrument in a place with excessive humidity,

vapor, excessive dust, fine powder, gas containing salt / sulfur / ammonia,

explosive gas, harmful smoke, or strong ultraviolet rays.

• Do not apply any input current exceeding the measuring range to the

instrument.

- 2 -

Содержание MCL-800D+

















Результаты поиска

Содержание MCL-800D+

Отзывы:

Похожие инструкции для MCL-800D+

Бренды по названию

Популярные бренды

MULTI MEASURING INSTRUMENTS MCL-800D+, Инструкция по эксплуатации

Результаты поиска

Содержание MCL-800D+

Отзывы:

Похожие инструкции для MCL-800D+

Бренды по названию

Популярные бренды