The Stick II
The Stick II
1 9
PROGRAMMING EXAMPLES
Turning “ON” your Unanswered Call Silent Transfer LINE 2
• DIAL “041” — “04” is the Register Number and “1” is the Program Range which means
“ON”
• Immediately listen for the “OK” tones (Bee-Bip), then the “PROCEED” tones (Bee-
Bee-Beep) or “ERROR” tones (low pitch beeps) then proceed. You have 30 seconds
to begin the next command.
Changing your Rings to Answer (RTA) LINE 1 and suppressing the
devices connected to Voice 1 from ringing during the RTA
• DIAL “1541” — “15” is the Register Number, next enter the Program Range of “41”.
"4" is the number of rings that will occur on every Line 1 phone before The Stick II
takes the call and processes it and “1” tells The Stick II to suppress any of the devices
hooked to Voice 1 from ringing until after the 4
th
ring.
• Immediately listen for the “OK” tones (Bee-Bip), then the “PROCEED” tones (Bee-
Bee-Beep) or “ERROR” tones (low pitch beeps) then proceed. You have 30 seconds
to begin the next command.
Changing the Security Access Code for Port 3
• DIAL “1137
*
6” — “11” is the Register Number and the Program Range is “37
*
6” —
the new access code for Port 3. See the Don’ts of SAC Programming before select-
ing your Access Code.
• Immediately listen for the “OK” tones (Bee-Bip), then the “PROCEED” tones (Bee-
Bee-Beep) or “ERROR” tones (low pitch beeps) then proceed. You have 30 seconds
to begin the next command.
DON’T FORGET TO SAVE AND EXIT PROPERLY
• DIAL “80”
• You will hear the “OK” tone TWICE (Bee-Bip, Bee-Bip). The LED will go back to
normal operation.
Remember: The only reason you would hear an error tone when saving and exiting is if you have programmed
all ports to default to Line 2 (can't enter programming mode from Line 2) and Auto-Line Select OFF on ALL
ports. You will be unable to Save & Exit until the situation is remedied. Assign a port to default to Line 1 or turn
Auto-Line Select ON for at least one port.
• Programming complete and changes are saved.
3 0
Factory preset Security Access Codes are as follows:
Voice 1/2(Port 1/2) =
“# 1”
Port 3
=
“
*
1”
Voice 2 (Port 2)
= “# 2”
Port 4 = “
*
2”
Port 5 = “
*
3”
Note: If limited access to your equipment is an issue, we recommend you change the
factory preset Security Access Codes upon installation.
Rings to Answer (RTA)
This feature directs The Stick II to answer an inbound call after a programmed
number of rings (0 to 9 rings) from the phone company. If RTA is programmed to “0”,
The Stick II will answer the call during the first ring. Extension phones (not attached to
The Stick II) in your location may only “chirp” on the first ring before going quiet.
When the RTA is greater than “0”, The Stick II will allow the incoming call to ring
extensions and the device connected to the voice port for that line. This feature also
allows you to suppress rings to the devices connected to the voice ports of The Stick II
during the RTA if you so choose. If a phone has not been picked up during the RTA,
then The Stick II will answer the call and process it according to its programming. Fac-
tory preset is 0 rings for immediate answer and suppression OFF.
Q:
Why would I ever want to have the RTA greater than 0 and suppressed?
A:
The Caller ID information comes from the telco between the first ring and
second ring. If you have Caller ID service and the ID equipment is on the
line side (before) The Stick II, you would want to set the RTA to be at least
2. Remember that if you connect your caller ID to the device port, you
need to set the "ring suppression" feature OFF.
Unanswered Call Silent Transfer
This feature was engineered for those of you who might receive manual faxes or modem
calls after normal business hours, but do not use an answering machine. Manual fax calls are
not accompanied by CNG fax tones and modem calls usually wind up routed to the phone
when the caller cannot execute the proper access code.
