manualshive.com logo in svg

Mueller SENTRY II, Инструкция по установке и эксплуатации, Страница: 31 / 83

Поделиться
Скачать
Mueller SENTRY II Скачать руководство пользователя страница 31

SECTION 4.0 - SENTRY II TEMPERATURE CONTROL

4.1

Sentry II Temperature Control and Thermocouple Sensor

The Sentry II control uses an electronic temperature control with digital display and a Type “T”
thermocouple sensor. The following installation and calibration procedures are very important to
ensure accurate sensing of the milk temperature.

4.2

Sentry II Thermocouple Sensor Installation 

Install the thermocouple sensor in the front-sensor raceway of the milk cooler as follows:

1.

Fabricate an insertion rod from a 5-foot piece of 10-gauge solid wire by forming a 

3

/

8

" open loop

on one end. See Figure 25. 

2.

Align the flat side of the “T” shaped sensor with the inner shell of the milk cooler.

3.

Slip the loop of the insertion rod over the thermocouple wire and push the sensor down the
raceway until it seats into the spring-clip at the end of the sensor raceway. 

4.

Being careful not to pull the thermocouple from the spring clip, withdraw the insertion rod from
the sensor raceway. See Figures 25 and 26.

Figure 25 - Sentry II Thermocouple Sensor Installation 

Sentry II with Auto-Dosing Assembly Operating Instructions

25

Effective April 1, 2000

Содержание SENTRY II




















































































Отзывы:

Нет отзывов