READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with the Treestand Manufacturers Association’s TMS 04 -
Standard Practice for Treestand Instructions
and TMS 02 -
Standard Test Method for Treestand Fall Arrest Systems.
attEntIon!!
WHEn You sEE a “ WarnInG!” BE surE to HEED tHE MEssaGE!
tHE InForMatIon contaInED In tHEsE MEssaGEs can saVE Your lIFE!!
7
Foot
Entrance
Heel Cord
Foot
Section
Cinching Straps/
Foot Straps
1
2
Foot
Entrance
Heel Cord
Foot
Section
Cinching Straps/
Foot Straps
1
2
Climbing
Cable
Foot
Section
Right
Support
A
Nylon
Washers
Secured
Cap Bolt
Foot
Section
WARNING!
Read the WEIGhT RESTRICTION WARNING, USAGE INSTRUCTIONS & WARNINGS and FUll-BOdy FAll ARREST hARNESS
USAGE INSTRUCTIONS & WARNINGS on pages 2-4 and pages 9-12 prior to assembly of this product! Failure to follow the instructions on this
page, pages 2-4 and pages 9-12 may result in serious injury or death!
WARNING!
aFtEr BEcoMInG FaMIlIar WItH Your stanDs’ assEMBlY, You Must rEaD anD FolloW all InstallatIon
InstructIons anD WarnInGs on PaGEs 13-15. FaIlurE to FolloW tHEsE InstructIons MaY rEsult In sErIous InJurY or DEatH!
WarnInG! this stand is equipped with a footrest. the footrest has not been designed to support the users weight. under no circumstances
shall you place any more than fifteen (15) pounds of weight on these structures. Doing so will put the user in serious risk of injury or death.
Failure to follow these instructions may result in serious injury or death
!
Refer to pages 13-15,
Field Installation
, for installation instructions.
stEP 1.
Unfold your stand, insert the
V-bracket
into the rear of the
foot section
and
secure using the
secured cap Bolt
. Repeat this STEP for the
seating platform
. (See both
notes
below)
stEP 2.
Attach the fixed end of (1)
climbing cable
to the
right support
of the
foot section
using (1) [A] 5/16’’ x 1
1/2’’ hex bolt, (2) nylon washers, (2) steel washers and (1)
5/16’’ nylock nut. Tighten securely. Repeat this STEP for the
installation of the
climbing cable
on the
seating platform
.
Secured
Cap Bolt
Foot Section
V-Bracket
Coated
Steel Chain
Snap Pins
Secured
Cap Bolt
Seat Section
V-Bracket
Bark Biters
Coated
Steel Chain
Snap Pins
Tab
V-Bracket
Bark Biters
Seat Section
Support - Right
Seat Section
Support - Left
Foot Section
Support - Left
Foot Section
Support - Right
notE:
V-Bracket installed
underneath the tab.
stEP 4.
Attach the
heel cord
to foot section.
To secure straps after installing, feed the open end of the
cinching
strap/foot strap
through the backside of
slot 1
. Loop over the top and
back through
slot 2
and pull to tighten. Repeat this STEP for the other
cinching strap/foot strap
(Fig. 1).
Foot Straps
and Heel Cord
installed
stEP 3
. Next, install (2) of the
cinching straps/foot straps
to the outside
of the
foot section
as shown below in Fig 1A.
note:
A 3rd cinching strap/
foot strap is included to secure sections together during transport.
Fig. 1
Fig. 1a
Loop
End
S-Hook
1.
Starting in the middle of the
foot platform
(See Fig. 1A from step
3), wrap the
loop end
of the
heel cord
around outside edge of
foot
platform
(Fig. 2).
2.
Thread the
s-hook
end through the
loop end
and stretch
heel cord
across the top of the
foot platform
to the other side. (Fig. 2).
3.
Wrap the
s-hook
end around the outside edge of the
foot platform
and attach the
s-Hook
around the
heel cord
to secure (Fig. 3).
Loop
End
S-Hook
Fig. 2
Fig. 3
Foot
Platform
Heel
Cord
Snap
Buckle
Zipper
1
2
3
Secured
Cap Bolt
V-Bracket
Tab
Nylon
Net
Secured
Cap Bolt
notE:
Stretch
nylon net
seat
so it is installed
underneath the
tab
and
V-bracket
(making sure
the top and bottom ends of the net are included).
Secure the
V-bracket and nylon net seat
using
the
secured
cap Bolt.
Make sure the
secured
cap Bolt
goes through the holes on the top and
bottom ends of
nylon net seat.
side View: securing nylon net seat
Snap
Buckle
Zipper
1
2
3
Secured
Cap Bolt
V-Bracket
Tab
Nylon
Net
Secured
Cap Bolt
