background image

Section 

E41•T41

 Page 519

Dated 

June 2016

97-4622-01-588

A.

 Parts

B.

 Repair Service

C.

 Warranty Service

D.

 Motors, Mechanical Seals, 

  and Accessories

6A Parts

Repair parts may be obtained 

through your local Authorized MTH 

Pumps Representative or Distributor 

who can be found in the yellow pages 

or by contacting MTH Pumps at:

 401 W. Main St. • Plano, IL 60545  

Phone: 630-552-4115

Fax: 630-552-3688

6B Repair Services

Repair service for an MTH pump 

should be obtained from the compa-

ny through which it was purchased.

6.

In the event this is not possible, the 

name and phone number of a nearby 

MTH representative or distributor 

may be obtained by contacting MTH 

Pumps.  In the event that it is neces-

sary to return the pump to the factory 

for repairs, remove all accessories 

attached to the pump.  We cannot 

accept responsibility for their safe 

removal, storage, and return.

6C Warranty Service

All requests for warranty claims 

should be made through the com-

pany from which the pump was 

purchased or supplied.  Complete 

details on what is wrong with the 

pump must be provided along with 

information on the system in which it 

is installed.  Refer to the MTH Pumps 

Limited Warranty statement.  Return 

authorization must be obtained prior 

to returning any equipment.

6D Motors, Mechanical Seals, and 

Accessories

Repair or replacement service on 

motors, mechanical seals, relief 

valves, or other accessories should 

be obtained from the manufacturer 

of these components. MTH does not 

carry replacement parts and is not 

authorized to render repair service 

on these components.  Replace-

ment mechanical seals are stocked 

at MTH and are always available 

insofar as possible for immediate 

shipment.  Warranty service, as well 

as expert application information 

can be obtained from your local seal 

manufacturer’s sales office.

Parts and Repair Services

E41•T41 SERIES

Содержание E41 Series





















Отзывы: