4
The Optional Remote Deflector - Part No. 01002278
Mounting Instructions
1.
Remove the right rear bolt holding the hopper to the
frame but save the nut. Install a 1/4-20 x 2" pan head
machine screw (Ref. 14), the rubber pad (Ref. 21) and
the deflector mounting bracket assembly and replace the
nut and tighten.
2.
Remove the upper handle mounting bolt on the right side
of the spreader and discard. Note: Save the 1/4-20
nylock nut.
a.
Install a 1/4-20 x 2" pan head machine screw (Ref. 14)
into the handle mounting hole.
b.
Install and tighten a 1/4-20 nut (Ref. 15) onto the pan
head machine screw.
c.
Install one 1/4" nylon washer (Ref. 5).
d.
Fit the lower hole in the pivot link (Ref. 13) over the end
of the machine screw.
e.
Install the second 1/4" nylon washer (Ref. 5).
f.
Install a 1/4-20 nylock nut (Ref. 4) and tighten until
snug.
3.
Drill a 9/32" hole in the upper handle assembly. (See
sketch below.)
4.
Put the threaded end of the control rod (Ref. 8) through
the lower control linkage hole (Ref. 12) and install the jam
nut (Ref. 11) but do not tighten the nut at this time.
5.
Install the control lever mounting bracket (Ref. 2) on the
bottom side of the handle assembly.
a.
Install a 1/4-20 x 1-1/4" pan head machine screw (Ref.
6) down through the hole you drilled in the handle
assembly.
b.
Fit the mounting bracket (Ref. 2) over this screw. Install
a 1/4-20 nylock nut (Ref. 4) and tighten.
6.
Slide deflector up towards the bottom of the hopper as
far as it will go.
7.
Place the control lever (Ref. 1) in the "OFF" position and
adjust the upper control rod nut (Ref. 9) so it is down
against the lower control linkage (Ref. 12). Now tighten
the jam nut (Ref. 11) up against the under side of the
control linkage.
8.
The rods on the deflector mounting bracket that the
deflector slides up and down on should be lubricated with
a thin grease to keep dust and dirt out of the openings.
Ref.
No.
Part No.
Description
Qty.
1
00060034
Operating Lever and Rubber Handle
1
2
00030417
Bracket, Dual Lever
1
3
00060057
Machine Screw, 1/4-20 x 7/8 Pan Hd.
4
4
00060036
Hex Nut, 1/4-20 Nylock
6
5
00018628
Flat Washer, 1/4 Nylon
10
6
00060047
Mach. Screw, 1/4-20 x 1-1/2 Pan Hd.
1
7
00010171
Retainer, "C" Clip
1
8
00035042
Threaded Rod, Deflector
1
9
00060071
Hex Nut. 5/16-18
1
10 00060073
Lock Washer. 5/16
1
11 00060072
Hex Nut, 5/16-18 Nylock
1
12 00035041
Deflector Arm
1
13 00035027
Flat Plate, Deflector
1
14 00060029
Machine Screw, 1/4-20 x 2 Pan Hd.
2
15 00060059
Hex Nut.1/4-20
1
16 00035030
Offset Bracket
1
17 01002275
Deflector Tube
1
18 00061065
Deflector Bracket
1
19 00061053
Flat Washer, 3/8
1
20 00061052
Cotter Pin, 1/8 x 1
1
21 00035851
Rubber Pad
1
NOTE: Adjust the friction at the
three deflector arm pivot points
by tightening the nuts and then
backing them off 1/8th turn. Ad-
just the friction at the operating
lever pivot so that it will hold its
position.
