background image

1.4 Limited Warranty 

INTEC Controls | MSR-Electronic GmbH

 does not assume any liability in case of improper or 

incorrect use of the de-vice. The installer and operator are exclusively responsible for the design 
and use of the product. If the product is not used, maintained or repaired in accordance with the 
instructions for use, warranty and product liability claims as well as claims arising from any 
guarantees assumed by 

INTEC Controls | MSR-Electronic GmbH

 for the product will be forfeited. 

INTEC Controls | MSR-Electronic GmbH

 warrants PolyGard

®

2/PolyXeta

®

2 devices against defects in 

material or work-manship for a period of 2 years (1 year for sensors) from the date of shipment. 
Should a defect in material or workmanship occur during the warranty period, 

INTEC Controls | 

MSR-Electronic GmbH

 will repair or re-place the unit at its option. This warranty does not apply to 

units that have been modified, after repair attempts, or that have been damaged unintentionally 
or intentionally. The warranty also does not apply to units in which the sensing element has 
been poisoned. The above warranty is in lieu of all other express warranties, obligations or 
liabilities. 

A pre-authorized RMA number issued by INTEC Controls is required for returns.

This warranty applies only to PolyGard

®

2/PolyXeta

®

2 units. 

INTEC Controls | MSR-Electronic 

GmbH

 is not liable for consequential damages resulting from the purchase or use of 

PolyGard

®

2/PolyXeta

®

2 devices. 

1.5 Dispose of Device 

In accordance with Directive 2012/19/EU, the device must not be disposed of as
municipal waste. Return the device for disposal to your national sales organisa-
tion, which you can contact if you have any questions about disposal.

Outside the EU, you have to consider the corresponding directives. 

In accordance with Directive 2012/19/EU, the device must not be 

disposed of as municipal waste. Return the device for disposal to your 

national sales organization, which you can contact if you have any 

questions about disposal. 

Outside the EU, you have to consider the corresponding directives.  

INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com

Specifications subject to change without notice. | GA_GC06_Modbus_supplement_E, 2022-04-05 | USA 221209 | Page 5 of 12

DGC6 Modbus Supplement – UserManual

Содержание Intec Controls PolyGard 2 DGC6













Отзывы: