manualshive.com logo in svg

MRMC MRMC-2118-00, Быстрый старт

Поделиться
Скачать
MRMC MRMC-2118-00 Скачать руководство пользователя страница 3

Round Rail Quick Start Guide

iii

Round Rail Quick Start Guide

Round Rail

Quick Start Guide

Contents 

Chapter  1 

Assembling the track ..................................................... 1

Safety........................................................................................ 1
Overview ................................................................................. 1

Before you start ............................................................. 1

Laying the first track section ................................................ 4
Anchoring the track............................................................... 5
Laying subsequent track sections......................................... 7
Mounting the rack ...............................................................10
Mounting the Cable Chain Tray ........................................13
Mounting Talos on the track ..............................................16

Attaching the track motor pinch wheel to Talos ....19
Mounting the Bumpers on Track .............................21

Adjusting Track Levelling after Mounting the Rig ..........21
Adjusting the Rig Wheels on the Round Rail...................23
Removing the trolley wheels from Talos...........................24
Mounting the Limit Switch and Datum Switch 
magnets on the rack.............................................................28

About track limits .......................................................28
Mounting the magnets ...............................................28

Содержание MRMC-2118-00





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды