MR VACUTAP Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 96

background image

5 Operation

Maschinenfabrik Reinhausen GmbH 2020

36

5788897/03 EN

VACUTAP

®

VVS

®

5 Operation

5.1 Operating the motor-drive unit with the hand crank

WARNING

Danger of explosion!

Unauthorized operation of the motor-drive unit with the hand crank may re-
sult in death or serious injury.

► Never operate the motor-drive unit electrically or with the hand crank be-

fore the transformer has been disconnected if you think there may be a
fault in the transformer or on-load tap-changer / de-energized tap-
changer.

► Never use the hand crank to complete a tap-change operation that has

begun electrically, but has not been ended completely.

► If the hand crank is difficult to move, you must stop using it.

► When operating the motor-drive unit with the hand crank, never reverse

the direction of rotation.

► If there is any doubt about the on-load tap-changer / de-energized tap-

changer being in proper working condition or about the cause of a fault in
the motor-drive unit, contact the Technical Service department of Maschi-
nenfabrik Reinhausen GmbH immediately.

► To operate the motor-drive unit manually, only use the hand crank

mounted in the motor-drive unit.

For information about fault rectification, refer to the "Fault elimination" chap-
ter.

Normal operation

During normal operation, there is no need to operate the unit with the hand
crank. The hand crank is mainly required during installation and for tests in
the transformer plant.

Use of the hand crank for operating the motor-drive unit is permitted if the
transformer is disconnected, e.g. for maintenance tasks, if there is no de-
tectable fault on the transformer or on-load tap-changer / de-energized tap-
changer and the previous tap-change operation has been completed cor-
rectly.

Emergency operation exception

An operation is considered an emergency operation if a tap-change opera-
tion is absolutely necessary when a transformer is energized, despite a fault
in the motor-drive unit. In this case, be sure to observe the warnings listed
above.

Operating the motor-drive unit with the hand crank

To carry out a tap-change operation with the hand crank, proceed as follows:

1. Open the door of the protective housing for the motor-drive unit.

«
...
34
35
36
37
38
...
»

Содержание VACUTAP

































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: Haigh Страницы: 60

Бренд: Federal Страницы: 43

Бренд: Quark-Elec Страницы: 2

Бренд: Guyatone Страницы: 2

TUV COMFORT LIGHT Series

Бренд: olympia electronics Страницы: 4

Бренд: Eaton Страницы: 2

Бренд: ATD Tools Страницы: 7

SPLICE-500 MKII

Бренд: Serpent Страницы: 8

Бренд: Wecan Technology and Lighting Co., Ltd Страницы: 4

Бренд: Game Winner Страницы: 25

Бренд: Anslut Страницы: 20

Бренд: EcoNet Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды