MQ Power WHISPERWATT DCA180SSK страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 98

background image

DCA-180SSK — PARTS AND OPERATION MANUAL— REV. #3 (06/11/09) — PAGE 45

DCA-180SSK — PRE-SETUP

Battery Cable Installation
ALWAYS

be sure the battery cables (Figure 30) are properly

connected to the battery terminals as shown below. The

RED

cable is connected to the positive terminal of the battery,

and the

BLACK

cable is connected to the negative terminal

of the battery.

When connecting battery do the following:

1.

DO NOT

connect the battery cables to the battery

terminals when the

Off/Manual/Auto

switch is in either

the manual or auto position (ON).

ALWAYS

make sure

that the Off/Manual/Auto switch is in the OFF position
when connecting the battery..

2. Place a small amount of grease around both battery

terminals. This will ensure a good connection and will
help prevent corrosion around the battery terminals.

CAUTION

CAUTION

CAUTION

CAUTION

CAUTION

:

Inadequate battery connections may cause
poor starting of the generator, and create
other malfunctions.

Wiring

Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.

Piping and Hose Connection

Inspect all piping, oil hose, and fuel hose connections for
wear and tightness. Tighten all hose clamps and check hoses
for leaks.

If any hose (fuel or oil) lines are defective replace them
immediately.

Figure 30. Battery Connections

If the battery cable is connected
incorrectly, electrical damage to the
generator will occur. Pay close attention
to the polarity of the battery when
connecting the battery.

CAUTION

CAUTION

CAUTION

CAUTION

CAUTION

:

Battery

This unit is of negative ground

DO NOT

connect in reverse.

Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level is not
properly maintained. Add only distilled water when
replenishment is necessary.
The battery is sufficiently charged if the specific gravity of

the battery fluid is 1.28 (at 68

°

F). If the specific gravity

should fall to 1.245 or lower, it indicates the battery is
discharged and needs to be recharged or replaced.
Check to see whether the battery cables are loose. Poor
contact may result in poor starting or malfunctions. Always
keep the terminals firmly tightened. Coating the terminals
with a thin film of grease will help inhibit corrosion.

«
...
43
44
45
46
47
...
»

Содержание WHISPERWATT DCA180SSK



































































































Отзывы:

Нет отзывов

Похожие инструкции для WHISPERWATT DCA180SSK

HOME NERATOR SYSTEM 18000 WATT

Бренд: GE Страницы: 84

Бренд: Promax Страницы: 14

Бренд: B&K Страницы: 2

Бренд: Mitsubishi Страницы: 12

Digiwatts RN3000US

Бренд: Renovo Страницы: 54

Бренд: C2G Страницы: 263

Бренд: ADF Web Страницы: 29

Бренд: Samlexpower Страницы: 20

Бренд: Extron electronics Страницы: 2

Бренд: Cross Technologies Страницы: 18

Бренд: DROPSA Страницы: 8

Бренд: Sennheiser Страницы: 2

Бренд: DSE Страницы: 2

Бренд: Wavetronix Страницы: 13

INVERTER PUMP CONTROL 5

Бренд: Profi-pumpe Страницы: 20

PV-ezRack SolarTerrace II

Бренд: Clenergy Страницы: 11

SUNNY BOY STORAGE 2.5

Бренд: SMA Страницы: 110

TFC-1000S70 - DATA SHEETS

Бренд: TRENDnet Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды