MQ Power WHISPERWATT DCA180SSK Скачать руководство пользователя | Manualshive

Страница: 10 / 98

background image

PAGE 10 — DCA-180SSK — PARTS AND OPERATION MANUAL — REV. #3 (06/11/09)

To reduce the possibility of an accident while transporting
the generator on public roads, always make sure the trailer
(Figure 1) that supports the generator and the towing vehicle
are in good operating condition and both units are
mechanically sound.

The following list of suggestions should be used when towing
your generator:

Towing Safety Precautions

■

ALWAYS

attach trailer's safety chain to bumper of towing

vehicle.

■

ALWAYS

make sure the vehicle and trailer directional,

backup, brake, and trailer lights are connected and working
properly.

■

Remember the maximum speed unless otherwise posted for
highway towing is

45 MPH

. Recommended off-road towing

is not to exceed

10 MPH

or less depending on type of terrain.

■

Place

chocked blocks underneath wheel to prevent

rolling

,

while parked.

■

Place

support blocks underneath the trailer's bumper to

prevent

tipping

, while parked.

■

Use the trailer's hand winch to adjust the height of the trailer,
then insert locking pin to lock wheel stand in place, while
parked.

■

Avoid sudden stops and starts. This can cause skidding, or
jackknifing. Smooth, gradual starts and stops will improve
gas milage.

■

Avoid sharp turns to prevent rolling.

■

Remove wheel stand when transporting.

■

DO NOT

transport generator with fuel in tank.

Check with your county or state safety
towing regulations department before
towing your generator.

■

Make sure the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer "gross vehicle
weight rating" (GVWR).

■

ALWAYS

inspect the hitch and coupling for wear.

NEVER

tow a trailer with defective hitches, couplings, chains
etc.

■

Check the tire air pressure on both towing vehicle and
trailer. Also check the tire tread wear on both vehicles.

■

ALWAYS

make sure the trailer is equipped with a "

Safety

Chain

".

DCA-180SSK — TOWING

Figure 1. Generator with Trailer

CAUTION:

CAUTION:

CAUTION:

CAUTION:

CAUTION:

«
...
8
9
10
11
12
...
»

Содержание WHISPERWATT DCA180SSK



































































































Отзывы:

Нет отзывов

Похожие инструкции для WHISPERWATT DCA180SSK

Бренд: NEC Страницы: 2

Бренд: Audio Note Страницы: 7

Бренд: Roland Страницы: 6

Бренд: SAJ Страницы: 59

ALL-USB-RS422/485

Бренд: Allnet Страницы: 6

Бренд: Badger Meter Страницы: 12

Бренд: Contec Страницы: 49

Бренд: SIIG Страницы: 32

Бренд: mundoclima Страницы: 60

Бренд: ZIPPER MASCHINEN Страницы: 52

Бренд: Logicform Страницы: 5

Бренд: UNICOM Страницы: 6

Бренд: Sollae Systems Страницы: 65

Бренд: EASTMAN Страницы: 20

Бренд: Panasat Страницы: 33

Бренд: AirMan Страницы: 69

Бренд: Zipper Mowers Страницы: 92

Бренд: Atomos Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды