MQ Power DA7000SSA3 Скачать руководство пользователя страница 45

Страница: 45 / 48

DA7000SSA3 GENERATOR• OPERATION MANUAL — REV. #0 (02/13/19) — PAGE 45

TROUBLESHOOTING (ENGINE AND GENERATOR)

Table 10. Engine and Generator Troubleshooting

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

Engine fails to start and

starter does not rotate.

Dead Battery?

Replace Battery.

Defective Starter Switch?

Replace Switch.

Defective Starter?

Replace Starter.

Fuse F5 Burned Out?

Replace Fuse.

Engine fails to start and

starter rotates.

Broken Pre-Heat Circuit?

Check Pre-Heat Circuit.

No Fuel?

Add Fuel.

Defective Wiring?

Check Wiring.

Engine starts "Idle Control

Switch" is in OFF position

and engine remains at low

speed.

Defective Idle Control Switch?

Replace Switch.

Clogged Fuel Strainer?

Clean or Replace.

Clogged Air Cleaner?

Clean or Replace.

Defective Idle Control Device?

Replace.

Disconnected Wiring?

Check and Repair Wiring.

Engine starts and "Idle

Control Switch" is in OFF

position. Engine speed rises

and battery discharges too

soon.

Defective Engine Regulator?

Replace Regulator.

Defective Wiring?

Repair or Replace Wiring.

Engine starts and "Idle

Control Switch" is in OFF

position. Engine speed

rises and engine seems

overloaded.

Defective Alternator?

Repair or Replace Alternator.

Damaged Alternator Bearing?

Replace Alternator Bearings.

Engine starts and "Idle

Control Switch" is in OFF

position. Engine speed rises

and engine has abnormal

noise.

Loose Engine Parts?

Check All Engine Parts For Tightness.

Defective Alternator?

Check Alternator for Damaged Bearing or

Loose Clamping Bolts.

Engine starts and "Idle Control

Switch" is in OFF position.

Engine speed rises and

remains at high speed when

Idle Control switch is placed

in the ON position.

Defective Idle Control Device?

Repair or Replace Idle Control Device.

Defective Idle Control Switch?

Replace Idle Control Switch.

Defective Solenoid?

Replace Solenoid.

Defective Relay?

Replace Relay.

Содержание DA7000SSA3

















































Результаты поиска

Содержание DA7000SSA3

Отзывы:

Похожие инструкции для DA7000SSA3

Бренды по названию

Популярные бренды

MQ Power DA7000SSA3, Руководство по эксплуатации

Результаты поиска

Содержание DA7000SSA3

Отзывы:

Похожие инструкции для DA7000SSA3

Бренды по названию

Популярные бренды