MQ Power DA7000SSA3 Скачать руководство пользователя страница 21

Страница: 21 / 48

DA7000SSA3 GENERATOR• OPERATION MANUAL — REV. #0 (02/13/19) — PAGE 21

30.

AC Voltmeter

— This voltmeter indicates (with a

mark) the rated 60 Hz (single-phase) output voltage.

In addition the voltmeter can also be used as a

diagnostic tool. If the voltmeter indicator (needle) is

below the rated voltage, engine problems may exist

(low/high RPM's). To prevent damage to the generator

or power tools turn the generator

OFF

and consult your

authorized Multiquip service dealer.

31.

Idle Control Switch

— The generator is provided with

an automatic idle control device for noise suppression

and reduced fuel consumption.
The automatic idle control automatically engages under

a no-load condition. With the automatic idle control

switched

, the engine revolutions will automatically

drop to about 2200 rpm (low-speed operation) within

3 seconds after the load stops. When the operation is

resumed, the engine speed is automatically increased

to about 3600 rpm (high-speed operation) as soon as

the load is connected.

32.

Engine Warning Lamps

— There are four engine

warning lamps, they are defined as follows:
a.

Low Oil Pressure Alarm Lamp

— During normal

operation of the generator this lamp

will remain OFF. When the ignition

switch is placed in the RUN position

to start the engine, the lamp will be

ON. When the oil pressure rises

after start-up the lamp will go OFF.

If this lamp is ever lit (

) during normal operation

of the generator, the emergency shutdown system

will stop the engine automatically.

Water Temperature Alarm Lamp

— This lamp

goes ON when the cooling water

temperature rises abnormally. If

the lamp goes ON during normal

operation of the generator, the

emergency shutdown system will

stop the engine automatically.

Battery Charge Alarm Lamp

— This lamp is

ON when the output voltage of

the alternator drops below a set

value. If this lamp is ON during

normal operation, the emergency

shutdown system will immediately

stop the engine.

Pre-Heat Lamp

— The pre-heat lamp will be ON

during the pre-heating cycle (cold weather

conditions). When the pre-heat cycle is completed

the lamp will turn OFF and the engine can be

started.

In addition this lamp displays

engine trouble shooting faults via

flashes (blinking). See engine

trouble codes in the maintenance

section of this manual.

33.

Starter Switch

— With key inserted turn clockwise to

start engine.

34.

Hour Meter

— Indicates number of hours machine

has been in use or hours engine was run.

Figure 6. Generator Components (3 of 3)

COMPONENTS (GENERATOR)

S-3031

CIRCUIT BREAKER

for 120V

20A

for 120V

30A

for 120V/240V

30A

AC VOLTMETER

HOUR METER

IDLE CONTROL

OFF

STOP

RUN

HEAT

START

STARTER SWITCH

QUARTZ

WHISPERWATT

7kW AC GENERATOR

ALL RECEPTACLES

G.F.C.I. PROTECTED

AC CIRCUIT BREAKER

G.F.C.I. PROTECTED

120V

240/120V

FULL POWER

SWITCH

A91110000

AUTO RESET

240

120

OFF

Содержание DA7000SSA3

















































Результаты поиска

Содержание DA7000SSA3

Отзывы:

Похожие инструкции для DA7000SSA3

Бренды по названию

Популярные бренды

MQ Power DA7000SSA3, Руководство по эксплуатации

Результаты поиска

Содержание DA7000SSA3

Отзывы:

Похожие инструкции для DA7000SSA3

Бренды по названию

Популярные бренды