MQ Multiquip MP115E Скачать руководство пользователя страница 33

Страница: 33 / 90

MP1 SERIES MASONRY SAW • OPERATION AND PARTS MANUAL — REV. #2 (10/12/17) — PAGE 33

TROUBLESHOOTING (BLADE)

Troubleshooting (Blades)

Symptom

Possible Problem

Solution

Blade slows or Stops cutting,still remains on

blade.

Blade too hard for the material being

cut?

Consult Dealer or Multiquip for correct blade. Try

cutting very soft material (sandstone, silica brick,

cinder block) to "Redress" the blade.

Engine Torgue diminished because of

loose V-Belts?

Tighten and/or replace V-Belts.

Insuffi cent Engine power?

Check Throttle setting. Check Engine horespower.

Improper direction of rotation?

Check that the blade is oriented and rotational

arrow points are in a "Down-Cutting" direction.

Blade is slipping on the blade shaft?

Check that the blade and fl ange pin are properly

installed on the blade shaft.

Blade does not cut straight and/or true.

Blade being used on misaligned saw?

Check blade shaft bearings and alignment

integrity.

Blade is excessively hard for the material

being cut?

Check specifi cations of the blade with the

material being cut. Consult Dealer or Multiquip for

information.

Blade being used at improper RPM?

Ensure blade surface feet per minute speed

(SFPM) is approximately 6,000.

Blade improperly mounted on arbor

shoulders and fl anges?

Ensure blade is properly affi xed on the blade

shaft.

Excessive force applied to blade while

cutting?

Do not force the blade in the cut. Apply a slow,

steady pace to sawing.

Blade discoloring, crackling and/or wearing

excessively.

Blade too hard for the material being

cut?

Consult Dealer or Multiquip for correct blade. Try

cutting very soft material (sandstone, silica brick,

cinder block) to"Redress" the blade.

Blade improperly mounted on arbor

shoulders and fl anges?

Ensure blade is properly affi xed on the blade

shaft. Ensure the blade fl anges are clean and free

of debris.

Blade not receiving enough cooling

water?

Ensure proper fl ow and volume of water is

provided for blades.

Abor hole out of round?

Ensure blade is properly affi xed on the blade

shaft.

Incorrect blade chosen for material being

cut?

Check specifi cations of the blade with the

material being cut. Consult Dealer or Multiquip for

information.

Excessive force applied to blade while

cutting?

Do not force the blade in the cut. Apply a slow,

steady pace to sawing.

Содержание MP115E



























































































Результаты поиска

Содержание MP115E

Отзывы:

Похожие инструкции для MP115E

Бренды по названию

Популярные бренды

MQ Multiquip MP115E, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MP115E

Отзывы:

Похожие инструкции для MP115E

Бренды по названию

Популярные бренды