manualshive.com logo in svg

MPE CHAIN-VEY, Руководство по установке и эксплуатации

Поделиться
Скачать
MPE CHAIN-VEY Скачать руководство пользователя страница 3

                                                               

 

 

2 

General Information:

 

 

Safety Recommendations and Warnings

 

 

MPE Chain-Vey

 

conveyors are built and tested to comply with current safety regulations and laws. 

To continue this practice of safety, MPE requires that the following is noted: 
 
Before installing, operating, or servicing the conveyor, it is necessary to completely understand the 
information found in this manual. 
 
The tubular drag conveyor is designed to be operated only as specifically stated in this manual. 
MPE can only warrant safety and proper performance of equipment that is used in accordance with 
this manual. 

 

 

All planning, installation, transport, assembly, commissioning, maintenance and repair (mechanical 
and/or electrical) may only be completed by qualified personnel. 
 

Safety Instructions 

1.

 

Do not attempt to install, connect power to, operate or service Chain-Vey equipment 
without proper instructions, or until you have been thoroughly trained in its use. 

 
2.

 

Do not attempt to work on, clean, or service the conveyor until the power has been turned 
off and locked out.  If and when it is necessary to momentarily start and stop (jog) the 
conveyor, use extreme caution and ensure that all personnel are clear of the conveyor 
chain. 

 

3.

 

Do not manually override or electrically bypass any protective device. 

 

4.

 

Do not connect power to, or operate the conveyor unless all moving parts are covered and 
all covers, guards, safety grids and maintenance panels are in place and securely fastened. 

 

5.

 

Do not place any part of your body or loose clothing within the feed hoppers, discharge 
hoppers, or any other access point on the conveyor while it is in operation. 

 

6.

 

All conveyor inlet and discharge openings and access panels must be completely enclosed 
to prevent human access when the conveyor is running and remain enclosed until power 
has been turned off and locked out. 

 

7.

 

All protective covers, guards, grates, maintenance panels and warning decals must be kept 
in place.  Any equipment with damaged, defective, or missing protective devices must be 
taken out of service until such protective devices can be repaired or replaced. 

 

No portion of this document may be reproduced in any format without written authorization by MPE 

Содержание CHAIN-VEY



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды