MPE CHAIN-VEY Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 26

MPE CHAIN-VEY Скачать руководство пользователя страница 12

11

Chain / Disc:

Chain-Vey chain is custom made and is rated for a minimum breaking load of 9,000 lbs [4,082 kg].
Conveying discs are molded from FDA compliant, ultra low friction UHMW. The weight of the
chain and molded discs is approximately 2.11 lbs/ft [3.14 kg/m].

Installation:
After the tubing circuit is installed, use a cable-puller or wire snake, equipped with a steel cable to
route through the conveying tube. Connect the chain to the cable and pull or winch the chain
through the tube.  It is very important to avoid twists in the chain.  One method to ensure the chain
is not twisted is to mark a point, for example the “top” of each disc with a marker. When the chain
is fed into the system, be sure to always feed the discs with the mark oriented in the same direction.
Such as the “top” always up.

CORRECT

INCORRECT

Once the chain is pulled through the system, cut off any excess chain links with a grinder/cutting
wheel or large bolt cutter. When cutting the chain, always error on the conservative side by leaving
a few more links than will probably be needed. Be sure that the connector link is spaced between
two empty links so it is spaced where a puck should be located. The chain ends can then be
connected using the provided chain connector.

«
...
10
11
12
13
14
...
»

Содержание CHAIN-VEY



























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды