Moyer Diebel 201HT M4 Series Скачать руководство пользователя страница 27

Страница: 27 / 120

201HT - Installation

Detergent and Rinse-aid Pumps and Injection Points - 201HT

201HT Control Panel

1. The chemical dispensing pump supply lines must be primed before they will pump the

chemicals properly.

2. Make sure the chemical containers are full and the correct pick-up tubes are in their

containers.

3. Turn the dishwasher power switch ON. The switch will illuminate and the dishwasher

will fill with water.

4. Open the dishwasher door, then push

and hold the prime push button UP to the

DETERGENT position until detergent is

observed entering the wash tank compartment

through the fitting located on the back right

corner of the tank. Release the push button.

5. Push and hold the prime push button DOWN

to the Rinse-aid position until you see air

bubbles moving through the rinse-aid tubing

coming out of the chemical container. Release

the push button.

6. Close the door to complete the priming operation.

PRIME

DETERGENT

RINSE AID

! VERY IMPORTANT !

The chemical dispensing pumps must be primed before operating the dishwasher and

whenever the chemical container is changed.

Priming the Dispensing Pumps

(continued on next page)

Содержание 201HT M4 Series

























































































































Результаты поиска

Содержание 201HT M4 Series

Отзывы:

Похожие инструкции для 201HT M4 Series

Бренды по названию

Популярные бренды

Moyer Diebel 201HT M4 Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание 201HT M4 Series

Отзывы:

Похожие инструкции для 201HT M4 Series

Бренды по названию

Популярные бренды