Moyer Diebel 201HT M4 Series Скачать руководство пользователя страница 75

Страница: 75 / 120

201HT Only - Booster Heater/Wash Tank Heater Interlock Circuit Operation

Booster Heater/Wash Tank Heater Interlock Circuit Operation

For Model 201HT,

the booster heater/wash tank heater interlock circuit removes

power from the wash tank heater whenever the booster heater contactor energizes.

The illustration below shows how the booster heater contactor is wired.
The booster heater contactor is located on the center of the base behind the lower front access

panel.

Interlock Circuit Operation

1. The dishwasher fills with water when the main power switch on the dishwasher is turned on.

The booster heater thermistor calls for heat which energizes the booster heater contactor.

2. The auxiliary contact on the top of the contactor opens and removes power from the

wash tank heater.

3. When the booster heater thermister is satisfied, the booster heater contactor de-energizes

and the auxiliary contacts close applying power to the wash tank heater.

4. This operation is repeated whenever the booster thermistor calls for heat.

To booster

heater contactor

1PH

208-230VAC

Auxiliary

Contactor

115VAC

No power when booster

heater is connected for 1 PH

No power when booster

heater is connected for 1 PH

Main Terminal Block (MTB)

To wash

tank heater

115VAC

From

main

terminal block

115 VAC

From

main

terminal block

1 PH

208-230VAC

No power

when booster

heater is

connected for

1 PH

No power when booster

heater is connected for 1 PH

To booster heater

1 PH 208-230VAC

1H2

1H3

1H1

Auxiliary

Contactor

Booster Heater

Contactor

Содержание 201HT M4 Series

























































































































Результаты поиска

Содержание 201HT M4 Series

Отзывы:

Похожие инструкции для 201HT M4 Series

Бренды по названию

Популярные бренды

Moyer Diebel 201HT M4 Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание 201HT M4 Series

Отзывы:

Похожие инструкции для 201HT M4 Series

Бренды по названию

Популярные бренды