Mouvex C4 A HT Скачать руководство пользователя страница 17

Страница: 17 / 29

17/29

NT 1004-H00 10 16 SLS24 i - SLS36 i e

6.1 Assembly / Dismantling

• Disconnect the pump from the discharge pipe.

• Unscrew the 8 nuts

106

and remove the 8 tierods

105

and

107

• Remove the front cover

401

. If the discharge piping is

mounted in a rigid manner, pivot the bottom

401

so as

to free the connection.

• Remove the outlet tube

402

and its seals

205

Before any dismantling, make sure that the
pump has been drained and take the necessa-
ry measures to avoid starting-up. No start-up,
even accidental, must be allowed.

6. OPENING OF THE PUMP

CAUTION

THE PUMP LUBRICANT IS VERY SLIPPERY
AND MAY CAUSE SERIOUS INJURY. ANY
SPILLS MUST BE CLEANED UP.

Slippery lubricant.

Spills should be

cleaned up.

WARNING

BE CAREFUL WITH THE WEIGHT OF THE
PARTS WHEN THEY ARE BEING REMOVED.

The weight ot the parts

can be dangerous and

may provoke bodily

injuries or material

damages.

WARNING

TAKE ALL NECESSARY MEASURES TO
RENDER ANY START-UP, EVEN ACCI-
DENTAL, OF THE PUMP DURING THE
WORK IMPOSSIBLE.

Any unforeseen start-up

can cause serious

injuries or important

material damages.

WARNING

FAILURE TO RELIEVE THE SYSTEM
PRESSURE PRIOR TO PERFORMING
ANY WORK ON THE PUMP OR THE
INSTALLATION CAN CAUSE PERSONAL
INJURY OR PROPERTY DAMAGE.

Hazardous pressure

can cause

personal injury

or property damage.

WARNING

DISCONNECTING THE FLUID OR PRES-
SURE CONTAINMENT COMPONENTS
DURING PUMP OPERATION CAN CAUSE
SERIOUS PERSONAL INJURY, DEATH OR
MAJOR PROPERTY DAMAGE.

Hazardous pressure

can cause

personal injury

or property damage.

WARNING

IF PUMPING HAZARDOUS OR TOXIC
FLUIDS, THE SYSTEM MUST BE
FLUSHED PRIOR TO PERFORMING ANY
SERVICE OPERATION.

Hazardous or toxic

fluids can cause

serious injury.

Содержание C4 A HT






























Результаты поиска

Содержание C4 A HT

Отзывы:

Похожие инструкции для C4 A HT

Бренды по названию

Популярные бренды

Mouvex C4 A HT, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание C4 A HT

Отзывы:

Похожие инструкции для C4 A HT

Бренды по названию

Популярные бренды