background image

ZD340_07d_e.doc / Apr-17

Page 19 / 50

4.8. Cut-to-Length Control Counter: F07.062 = 7 or 8

The cut-to-length function described here requires the use of a counter model possessing at

least two front thumbwheel switches.

Modes 7 and 8 serve for control of cut-to-length applications with line drives providing a fast –
slow – stop speed profile. The table below explains which functions are assigned to the

thumbwheels and preset registers

Preset

Function

Explanation

Thumbwheel 1

Tool Width

Compensates the cutting length setting by the

width of the saw blade or cutting tool

Thumbwheel 2

Cutting Length

Desired total length of the piece to cut

Preset register

F01.004

(keypad entry)

Pre-Stop

Anticipation distance where the speed changes
from high to low before reaching the final position.

Preset register

F01.005

(keypad entry)

Correction Stop

Correction of the overshoot distance which the drive

produces when changing from low speed to stop

Preselection registers K1 to K4 (F01.000 to F01.003) are not available for any settings, since this

application uses the same registers for calculations and intermediate results.
With operation mode F07.062 set to 7, the counter starts from zero and counts up until reaching

the value of “Cutting Length plus Tool Width”. With operation mode F07.062 set to 8, the start

signal presets the counter to the negative value of the Tool Width, from where the counter
counts up until it reaches “Cutting Length”

All other functions are fully similar with these two modes.
This mode provides display of the actual position only and also the analogue output (if
applicable) is assigned to the actual counter value.

Measuring wheel

Encoder

A,B

En co der 1

1 2 3 4 5 6

Out2

Out3
Out4

Run comma nd
Fast / Slow select

Rea dy to cu t

Start command

Содержание ZA 330



















































Отзывы: