Motorola AP-5181 - Wireless Access Point Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 40

background image

26

AP5181 Access Point

As an option (not displayed above), the ring seal can be inserted into the receiving threaded hole of the
gland housing. The receiving threaded hole is in the hexagonal section of the gland housing stamped

LTW

(see the illustration under step 2). Ensure the ring seal is seated at the bottom of the threaded hole

.

4.

Assemble the gland assembly, finger nut, flange barrel and modular connector onto the cable. You are now
ready to install the connector face gasket.

5.

Remove the adhesive liner on the gasket. Slide the gasket over the connector and along the cable, with
the adhesive facing the flange surface of the flange barrel.

NOTE

The modular connector is intended to be wired specifically. It is extremely important to
wire the connector per industry standards for Ethernet, non cross- over configuration).
The applicable standard is TIA/EIA 568-A.

«
...
24
25
26
27
28
...
»

Содержание AP-5181 - Wireless Access Point









































Отзывы:

Нет отзывов

Похожие инструкции для AP-5181 - Wireless Access Point

Бренд: Abus Страницы: 60

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 32

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

Бренд: Javad Страницы: 35

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

Бренд: ProCurve Страницы: 2

Бренд: Advantech Страницы: 36

Бренд: CyberTAN Страницы: 67

Бренд: ACTi Страницы: 12

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

Бренд: NCR Страницы: 15

Бренд: Acromag Страницы: 23

Бренд: Top Страницы: 21

NVR41-4KS2 Series

Бренд: Dahua Страницы: 452

Бренд: Digisol Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды