Motorola AP-5181 - Wireless Access Point Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 40

background image

Deployment Guide

21

14. Ensure no loose hardware is inside the housing. Check the wiring to be sure it is clear of the cover.

Carefully replace the cover. Only the correct cover orientation (as displayed below) allows all screws to
be properly installed.

15. Tighten all 10 screws securely. Torque all screws to 15-20 in-lbf. Hand tighten only. Do not use power

tools.

16. The Power Tap can now be installed.

17. Add the required grounding lug or cable (not included with this product) the earth ground boss.

NOTE

Please locate the earth ground boss under the bracket of the Power Tap. This point
must be properly grounded to earth to utilize this product’s safety features.

«
...
19
20
21
22
23
...
»

Содержание AP-5181 - Wireless Access Point









































Отзывы:

Нет отзывов

Похожие инструкции для AP-5181 - Wireless Access Point

OXTOPUS EIA-709

Бренд: OCCITALINA Страницы: 54

Бренд: Furuno Страницы: 24

Бренд: LevelOne Страницы: 31

F-Tile SDI II Intel Agilex

Бренд: Intel Страницы: 39

Active Module Carrier VX402C-64

Бренд: C&H Страницы: 32

Бренд: Jøtul Страницы: 20

Бренд: Cervoz Страницы: 22

Quadro M6000 Sync

Бренд: Nvidia Страницы: 8

SiliconDrive SSD-P16G(I)-3100

Бренд: Silicon Systems Страницы: 108

Бренд: Arduino Страницы: 25

SRA311-008P8 Series

Бренд: Divio Страницы: 4

Бренд: DigiTech Страницы: 6

Бренд: Nortel Страницы: 163

Бренд: Baracoda Страницы: 16

Бренд: Ista Страницы: 16

Бренд: Sierra Wireless Страницы: 2

ADSL Ethernet & USB Combo Router Lynx L-510

Бренд: Starbridge Networks Страницы: 59

Бренд: uneron Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды