Motorola AP-5181 - Wireless Access Point Скачать руководство пользователя страница 17

Страница: 17 / 40

Deployment Guide

• The instructions provided herein are intended to provide useful installation guidance, and offer insight into best

practices. Adherence to this guide, and the instructions herein do not ensure compliance with specific or
regional electrical codes and regulations.

• In all cases, specific or regional electrical codes and regulations shall govern the installation of this product.

• Installation and maintenance of this product in compliance with specific or regional electrical codes and

regulations is the sole responsibility of the end user.

To install an AP-5181 Power Tap:

Remove and retain the 10 screws used to secure the Power Tap cover.

Remove the weather sealing cover to expose the unit’s interior. Do not remove or tamper with the sealing
gasket remaining on the back housing.

Remove and retain the 2 terminal screws releasing the 2 solder-less ring terminals.

Содержание AP-5181 - Wireless Access Point









































Результаты поиска

Содержание AP-5181 - Wireless Access Point

Отзывы:

Похожие инструкции для AP-5181 - Wireless Access Point

Бренды по названию

Популярные бренды

Motorola AP-5181 - Wireless Access Point, Руководство по развертыванию

Результаты поиска

Содержание AP-5181 - Wireless Access Point

Отзывы:

Похожие инструкции для AP-5181 - Wireless Access Point

Бренды по названию

Популярные бренды