background image

12A

12B

EN

EN

RTX 2252-SENSOR MODULE (OPTIONAL)

• 

Powered by stacks

2x 1,5V DC Alcaline (AA)

• 

Operating Frequency

868 MHz FSK Band

• 

System capacity in free field

10 + 20 m máx.

• 

Operating temperature

- 10 to +55°C

• 

Dimensions

120x80x50mm

• 

External material

ABS  UL94V-0  (IP56)

1,5V  battery tipe AA

SAFETY 

DEVICE

INHIBITOR

1,5V  battery tipe AA

TX

CN1

RTX

SET

SW1

SW2

1

1

2

2

1
2
3
4

• TECHNICAL SPECIFICATIONS

01

 • Safety device input (NC) or 8K2.

02

 • Safety device input (NC) or 8K2.

03

 • Inhibitor input (NC)

04

 • Inhibitor input (NC)

CN1

• OPERATION

The RTX 2252 device (sensor) allows the connection of safety bands of the classic type 

NC (normally closed contact) or 8K2 Ohm resistive type.

This sensor operates only in combination with the control base - 2278 RTX.

The device is powered with stacks, avoiding any cable connection. 

After stored in RTX 2278 device, sends you the following information:

 Survival signal:

 Check periodically if the radio connection between the devices is 

functioning properly and informs the base.

 Alarm signal:

 Tells the basis that the safety device is activated.

03. CONFIGURATION

RTX 2252-SENSOR MODULE (OPTIONAL)

Setting the frequency A, B, C or D in RTX 2252 must be coincident with the RTX 2278 

base module configuration (

see page 11A

).

ON

OFF

FREQUENCY B

1

2

SW1

FREQUENCY C

1

2

SW1

FREQUENCY D

2

1

SW1

1

2

SW1

FREQUENCY A

DIP 1= OFF

 - Type NC Classic (standard)

Normally Closed

DIP 1=ON

 - Type Resistive 8K2 Ohm 

Operation

ON

OFF

1

2

NC

SW2

ON

OFF

1

2

8K2

SW2

When the inhibitor input is not used, it should always be made a bridge 

(jumper) between 3 and 4 inputs.

 Discharged stack signal:

 Tells the base the stack status.

Operation with Contact Inhibitor:

The RTX 2252 device (sensor) enables the connection of a contact (NC) for temporarily 

inhibiting of the safety band connected to the sensor.

With the application of one micro-switch (CN1, connector 3 and 4), the band can be 

disabled for the motor does not reverse when it reaches the end of the closure and 

presses the band.

Aplique 1 micro (NC), de forma que comute para NA centímetros antes da banda com-

primir. 

In this case, the band can be pressed without causing reverse movement.

03. CONFIGURATION

Содержание MC15SC


















Отзывы: