9A
9B
EN
EN
A very low value in this parameter may cause the engine to not have enough
torque to move the gate and the effort error occurs ( or
).
Force adjustment
Allows you to set the force that is injected
into the motor when it moves at normal
speed.
Sensivity adjustment
Allows to adjust the sensivity of the motor
in the presence of obstacles. The higher the
sensivity, the less effort it will take to detect
any obstacle and reverse direction.
min.
max.
1
9
Default value (
05
)
min.
max.
1
9
Default value (
05
)
DECELERATION TIME ADJUSTMENT
AJUSTE DO TEMPO DE ABRANDAMENTO
COURSE PROGRAMMING
Manual programming:
01
• Press MENU for 2 sec. until
appears.
02
• Press MENU once until
appears.
03
• Press MENU
(or remote control)
to start programming the opening time.
01
• Press MENU for 2 sec. until it appears
.
02
• Use UP until appears
.
03
• Press Menu will appear
. Use UP or DW to navigate the parameters.
04
• Press MENU to edit the chosen parameter value.
05
• The factory set time appears. Use UP and DW to change the value.
06
• Press MENU to save the new value.
07
• Press MENU again.
08
• Use UP and DW to display
to exit programming mode.
09
• Use UP and DW to stay in Standby.
This menu allows to set the deceleration time of each leaf at opening and closing.
Slowing down on opening leaf 1
It allows to define the time that the gate will
act with slowdown in the opening.
Slowing down on closing leaf 1
It allows to define the time that the gate will
act with slowdown in the closing.
Slowing down on opening leaf 2
It allows to define the time that the gate will
act with slowdown in the opening.
Slowing down on closing leaf 2
It allows to define the time that the gate will
act with slowdown in the closing.
Default value (
03
)
min.
max.
0s
25s
04. PROGRAMMING "P"
04. PROGRAMMING "P"
04. PROGRAMMING "P"
FORCE AND SENSIVITY ADJUSTMENT
DIRECTION OF
DISPLAY ROTATION
COURSE PROGRAMMING OF TWO MOTORS
Normal rotation - leaf 1 starts opening (normal speed)
Slow rotation - leaf 1 goes into opening slowdown (slowdown speed)
Normal rotation – leaf 1 stops and leaf 2 starts opening (normal speed)
Slow rotation - leaf 2 goes into opening slowdown (slowdown speed)
Normal rotation – leaf 2 stops and starts closing (normal speed)
Slow rotation - leaf 2 goes into closing speed (slowdown speed)
Normal rotation - leaf 2 stops and leaf 1 starts opening (normal speed)
Slow rotation - leaf 1 goes into closing slowdown (slowdown speed)
2 MOTORS ( = )
1 MOTOR (PEDESTRIAN) ( = )
04
• Press MENU to start the opening slowdown
of leaf 1. Repeat these two steps (03 and 04)
for leaf 2.
05
• Press MENU to start programming the
closing time of leaf 2.
06
• Press MENU to start the closing slowdown
of leaf 2. Repeat these two steps (05 and 06)
for leaf 1.
07
• Press MENU once to display
, leaf 1
stops.
08
• Use UP and DW to display
to exit
programming mode.
09
• Use UP and DW to stay in Standby.
04
• Press MENU to start the opening slowdown
of the leaf.
05
• Press MENU to stop the leaf and start
programming the closing time.
06
• Press MENU to start the closing slowdown
of the leaf.
07
• Press MENU once to display
, leaf 1
stops.
08
• Use UP and DW to display
to exit
programming mode.
09
• Use UP and DW to stay in Standby.
COURSE PROGRAMMING OF ONE MOTOR (PEDESTRIAN)
Normal rotation - leaf starts opening (normal speed)
Slow rotation - the leaf goes into opening slowdown (slowdown speed)
Normal rotation - the leaf stops and starts closing (normal speed)
Slow rotation - the leaf goes into closing slowdown (slowdown speed)
Course Manual Programming
This menu allows you to manually set the course of
the leaf/leaves.
Number of Motors
Allows you to define the number of motors connected
to the control board
Default value (
NA
)
Default value (
02
)
After selecting the number of motors connected to the control board, return to the
menu to do manual programming.
