background image

SILVER Line microscopes are designed to function with minimal maintenance, but certain 

components should be cleaned frequently to ensure ease of viewing. The power switch 

should be turned off or the microscope should be unplugged when not in use.

CLEANING

The front lens of the objectives (particularly the 40XRD and 100XRD) should be cleaned 

after use. The lens surface may be gently cleaned with a soft camel hair brush, or blown off 

with clean, oil-free air to remove dust particles. Then wipe gently with a soft lens tissue, 

moistened with optical cleaner (eyeglass or camera lens) or clean water. Immediately dry 

with a clean lens paper.

CAUTION

Objectives should never be disassembled by the user. If repairs or internal cleaning should 

be necessary, this should only be done by qualified, authorized microscope technician. The 

eyepiece(s) may be cleaned in the same manner as the objectives, except in most cases 

optical cleaner will not be required. In most instances breathing on the eyepiece to moisten 

the lens and wiping dry with a clean lens tissue is sufficient to clean the surface. Lenses 

should never be wiped while dry as this will scratch or otherwise mar the surface of the glass.

The finish of the microscope is hard epoxy and is resistant to acids and reagents. Clean this 

surface with a damp cloth and mild detergent.

Periodically, the microscope should be disassembled, cleaned and lubricated. This should 

only be done by a qualified, authorized microscope technician.

DUST COVER AND STORAGE

All microscopes should be protected from dust by a dust cover when in storage or not in use. 

A dust cover is the most cost-effective microscope insurance you can buy. Ensure that the 

storage space is tall enough to allow the microscope to be placed into the cabinet or onto a 

shelf without making undue contact with the eyepieces. Never store microscopes in cabinets 

containing chemicals which may corrode your microscope. Also, be sure that the objectives 

are placed in the lowest possible position and the rotating head is turned inward and not 

protruding from the base. Microscopes with mechanical stages should be adjusted toward 

the center of the stage to prevent the moveable arms of the mechanical stage from being 

damaged during storage in the cabinet.

TENSION CONTROL OF FOCUSING MOVEMENT

Tension of the focusing movement is controlled by a tension system found on the pinion of

the coarse focus control. This can be adjusted by using the wrench included with the 

microscope. 

TIGHTENING

DIRECTION

SILVER

250

 

SERIES

 

|  12 

  

CARE AND CLEANING

SILVER

 LINE

Содержание 1100104800031
















Отзывы: