background image

XT0016

Installation & Maintenance Manual

•  The installation of this fireplace must be done by a 

qualified and certified gas appliance installer.

•  Check local codes and read all instructions prior to 

installation.

®

C

US

       WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, 

death, or property damage.

— Do not store or use gasoline or other flammable vapors and 

liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do not use any 

phone in your building.

•  Leave the building immediately.
•  Immediately call your gas supplier from a neighbour's 

phone. Follow the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire 

department.

— Installation and service must be performed by a qualified 

installer, service agency or the gas fitter.

PROFLAME 2 UPGRADE KIT  

RX 200 + RX 300 NG/LP

 

Upgrade Kit NG/LP Proflame 2 

 

(Basic to Full Load with Remote)

THIS KIT IS FOR USE WITH THE FOLLOWING MODELS: 

RX200:

B34DT-2-F : B34 TOP VENT, ELECTRONIC IGNITION, IPI
B34DR-2-F : B34 REAR VENT, ELECTRONIC IGNITION, IPI
B38DT-2-F : B38 TOP VENT, ELECTRONIC IGNITION, IPI
B38DR-2-F : B38 REAR VENT, ELECTRONIC IGNITION, IPI
PL38DFN-F : PL38 , ELECTRONIC IGNITION, IPI
PL38DFL-F : PL38 , ELECTRONIC IGNITION, IPI
PL42DFN-F : PL42 , ELECTRONIC IGNITION, IPI
PL42DFL-F : PL42 , ELECTRONIC IGNITION, IPI
PL52DFN-F : PL52 , ELECTRONIC IGNITION, IPI
PL52DFL-F : PL52 , ELECTRONIC IGNITION, IPI

RX300:

DL6315NI : DL6315, ELECTRONIC IGNITION, IPI
DL6315STNI : DL6315ST, ELECTRONIC IGNITION, IPI

Ensure that all power to the appliance is off at the electrical breaker 

or fuse before beginning installation. Ensure gas is turned off at the 

shutoff valve before beginning installation.

When installing the fireplace - gas lines, fittings, accessories or any 

other objects cannot impede the proper movement of the door 

buckles.

CAUTION

WARNING

Some materials used in the manufacturing process of this product can 

expose you to Benzene which is known in the State of California to 

cause cancer and birth defects or other reproductive harm. For more 

information go to www.P65warnings.ca.gov

WARNING

Содержание Proflame 2 RX 300 LP













Отзывы: