background image

XG0128

Page 2

M38ODV-ST Direct Vented Fireplace

Introduction

The 

M38ODV-ST 

model with a continuous pilot, is a direct-vented

See-Thru Gas Fireplace with glass doors on two sides and an
adjustable burner

This manual covers the M38ODV-ST model unless otherwise speci-
fied. Sections which are specific to a particular model are marked with
a

      symbol, plus the appropriate model number.

The 

M38ODV-ST

 is rated for:

„

Natural Gas at 32,000 BTU/H (9.38 Kilowatts) Input

„

Propane at 32,000 BTU/H (9.38 Kilowatts) Input

The Montigo warranty will be voided by, and Montigo

 

disclaims any

responsibility for, the following actions:

„

Modification of the fireplace and/or components including Direct-
Vent assembly or glass doors.

„

Use of any component part not manufactured or approved by
Montigo in combination with this Montigo fireplace system.

„

Installation other than as instructed in this manual.

Consult your local Gas Inspection Branch on installation requirements
for factory-built gas fireplaces. Installation & repairs should be done by
a qualified contractor.

Installations in Canada

 must conform to the current 

CAN/CGA B-

149.1

 and 

.2

 Gas Installation Code and local regulations. When the

unit employs the 

optional

 Fan Kit, it must be electrically grounded in

accordance with 

CSA C22.1

 Canadian Electrical Code Part 1 and/or

Local Codes.

Installations in the USA

 must conform to the National Fuel Gas

Code, 

ANSI Z223.1-1988

. When the unit employs the 

optional 

Fan Kit

it must be grounded in accordance with local codes or, in the absence
of local codes, with the National Electrical Code, 

ANSI/NFPA 70-1987.

A manufactured (mobile) home

 OEM installation in the 

United

States 

must conform with the Manufactured Home Construction and

Safety Standard, 

Title 24 CFR, Part 3280

, or, when such a standard is

not applicable, the Standard for Manufactured Home Installations,

ANSI / NCSBCS A225.1

. In 

Canada

, the installation must conform to

the Standard for Gas Equipped Recreational Vehicles and Mobile
Housing, CSA Z240.4.

Table Of Contents

Introduction .............................................................................

2

Installation ........................................................................

3 - 11

Installing the Fireplace Shell ........................................... 3

Installing the Gasline ...................................................... 4

The Remote Switch ....................................................... 4

Direct Vent Installation ................................................... 4

General Requirements ...................................... 4

Terminations ..................................................... 5

Horizontal Venting Runs .................................... 6

Vertical Venting Runs ........................................ 8

Finishing around the fireplace

Facing ............................................................. 8

Mantels and Surrounds ..................................... 8

Installing the Logset ....................................................... 9

Removing and Installing the Door .................................. 9

Operation

Adjusting the Center Burner ........................................ 10

Lighting Instructions - Model M38ODV-ST ................... 11

Maintenance

Cleaning ...................................................................... 12

Pilot Burner Adjustment ............................................... 12

Gas Control Valve ........................................................ 12

Troubleshooting ........................................................... 12

Appendix A - Spare Parts & Accessories

............................ 13

Warranty

................................................................................. 14

CAUTIONS

Due to its high operating temperatures, the appliance
should  be located out of traffic & away from furniture and
draperies.
  

Children and adults should be alerted to the hazards
of the high surface temperature, which could cause
burns or clothing ignition.

  

Young children should be carefully supervised when
they are in the same room as the appliance.

  

Clothing or other flammable materials should not be
placed on or near the appliance.

Содержание M38ODV-ST

















Отзывы: