background image

5

© 2011 Monte Carlo Fan Company

3/8/2012

13

14

15

16

17

18

Make wiring connections using wire 

connectors provided as indicated above. 

Connect white wire from fan to white wire 

from house and then connect black and 

blue wires from fan to black wire from 

house. Connect all green grounded wires 

to Grounded wire from House. Make sure 

that no filaments are outside of the 

wirenuts.

Note

: This fan adapter is not available 

with Remote controller.  

Remove preassembled cross pin and 

keeper pin from adapter housing yoke at 

top of adapter assembly and partially 

loosen downrod set screws.

Place downrod over canopy, canopy 

bottom cap and yoke cover. 

Slip downrod into adapter housing yoke, 

align holes and reinstall cross pin and 

keeper pin. Evenly tighten downrod set 

screws on motor housing yoke.

Note

: Refer to installation step 22 if you 

want to replace downrod with longer one 

(not included). 

  

Determine the orientation of fan assembly 

you want and Install ball end of downrod 

into mounting bracket opening. 

Warning:

 Make sure the ball end of 

downrod engages with mounting bracket 

well to avoid personal injury.

For Canadian installation and for USA fan 

and light kit combinations over 35 lbs, in 

both flush and downrod mode the safety 

cable must be installed into the house 

structure beams using 3” lag screws, 

washers and lock washers provided. 

Make sure that when the safety cable is 

fully extended the leadwires are longer 

than the cable and no stress is placed on 

the leadwires. 

Loosen one and remove one 

preassembled canopy mounting screw 

from mounting bracket. Save canopy 

mounting screw. Lift canopy up, aligning 

its keyhole slot with the preassembled 

screws on mounting bracket and twist 

clockwise to lock in place. Re-install the 

removed canopy mounting screw and 

tighten all screws securely.

Attach canopy bottom cap onto canopy 

by aligning its notches with the 

preassembled canopy mounting screws 

on mounting bracket and twist clockwise 

until tight. 

Refer to fan installation instruction manual 

for blade assembly. 

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Black

White

Blue

Wall switch

Black

White Green

Ground/Green

Cross pin

Keeper pin

Canopy

Canopy bottom cap

Yoke cover

Downrod

Содержание MCDF series









Отзывы: