manualshive.com logo in svg

Montag C06B, Руководство по эксплуатации, Страница: 32 / 33

Поделиться
Скачать
Montag C06B Скачать руководство пользователя страница 32

32

7.4 MAINTENANCE SCHEDULE

Schedule follows time increment of whatever comes first.

Beginning/ending season, 

and every week or 1000 

hours

Beginning/ending season or 

1000 hours

Every 3 years or 5000 acres

Lubricate tie rod ends

X

Lubricate all other fittings

X

Service hub bearings and 

seals

X

8. S

toraGe

1. 

Cart should be cleaned by power washing to prevent fertilizer from causing corrosion during off season. Care should 

be taken to avoid areas where grease would be removed, decals would be damaged, or electrical connections.

2. 

Lubrication instructions should be followed, and complete any service or repair. 

3. 

Montag Auto Steer Cart should be stored in a location and manner where it is not subject to damage. It is recommended 

that the cart is not disassembled for storage.

9. p

artS

Refer to our Carts - Parts Manual in the Support section of our website at 

www.montagmfg.com

10. t

roubleShootInG

Problem

Possible Cause

Solution

Cart not tracking correctly.

Alignment is not correct.

Follow alignment procedures (Section 

4.1.3).

Cart arms not level in field position.

Hitch is out of adjustment.

Follow adjustment procedures 

(Section 3.3.8).

Hitch is at limit of adjustment.

Gusset may be in wrong location for 

desired adjustment.

Move gusset to opposite of cart arm 

(Section 3.3.8).

Tracks wearing unevenly.

Track tension  is out of adjustment.

Adjust track tension per Camso 

manual instructions.

Tracks wearing excessively.

Roading is too fast/long.

Do not transport above 15 MPH. See 

Camso operator's manual.

Содержание C06B


































Отзывы:

Нет отзывов