Montag C06B Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 33

Montag C06B Скачать руководство пользователя страница 22

22

3.5 LIQUID FERTILIZER SYSTEM ASSEMBLY

Crushing Hazard.

Be certain tie-downs straps at opposite

corners of tank are routed correctly and tight

before doing any assembly work.

Fertilizer can be dangerous to people,

animals, and the environment.

Read and follow the safety and handling

instructions provided by the fertilizer

manufacturer before filling fertilizer tank.

3.5.1 INSTALL LIQUID FERTILIZER SKID ONTO CART

1.

Verify tie down straps (A) are routed correctly as shown and

tight.

2.

Carefully position skid onto cart, with skid frame fully aligned

with cart frame and ends of skid frame overlapping cart frame

evenly.

Note: Install U-bolts facing up, with nuts on top. If U-bolts are

installed facing down, disassembly may be required if bolts need

to be removed.

3.

Install ⅝ x 4 x 6-1/2'' U-bolts (C) in each corner of skid inside cart bracket (B) as shown, with lock nuts on top. Tighten

lock nuts until they each contact the plate.

4.

Alternately tighten nuts on each leg of U-bolt in 25 lb increments until each nut is tightened to 75 lb/ft of torque. Then

tighten each nut to 95 lb/ft of torque. Do not over tighten.

A

«
...
20
21
22
23
24
...
»

Содержание C06B


































Отзывы:

Нет отзывов