manualshive.com logo in svg

Montag C06B, Руководство по эксплуатации, Страница: 30 / 33

Поделиться
Скачать
Montag C06B Скачать руководство пользователя страница 30

30

5. 

Remove bushing (A).

Note: To avoid damaging bushing, install with a non-marring 

implement, such as a rubber mallet, or with a block of wood to 

protect bushing during installation.

6. 

Install  new  bushing  with  a  non-marring  implement  until 

outer end of bushing is flush with pin sleeve.

7. 

Install spindle assembly. (See Section 3.3.3)

8. 

Install wheel. (See Section 3.3.6)

9. 

Remove cart supports and lower cart.

7.2 ARM BUSHINGS

Note: Arm assembly has bushings at top and bottom of pin sleeves. Bushings should be replaced in pairs (top and bottom 

of sleeve together).

Prevent death or serious injury.

Arm assembly weighs approximately 470 lbs (213 kg).

Use adequate lifting and support devices.

1. 

Remove all product from tank.

 

2. 

Remove  arm  assembly  using  an  adequate  lifting  device. 

Remove  only  one  arm  assembly  at  a  time  and  ensure 

opposite  arm  is  adequately  secured  to  prevent  cart  from 

tipping over.

3. 

Remove bushing (A).

Note: To avoid damaging bushing, install with a non-marring 

implement, such as a rubber mallet, or with a block of wood to 

protect bushing during installation.

4. 

Install  new  bushing  with  a  non-marring  implement  until 

outer end of bushing is flush with pin sleeve.

5. 

Install arm assembly. (See Section 3.3)

Содержание C06B


































Отзывы:

Нет отзывов