manualshive.com logo in svg

Monogram ZIP360NH, Руководство по установке

Поделиться
Скачать
Monogram ZIP360NH Скачать руководство пользователя страница 38

38

Installation Instructions

INSPECT FINAL INSTALLATION

Check door alignment
Stand back away from the refrigerator to inspect the 
final installation.
• Installation or the addition of heavy door panels 

may have caused the doors to move slightly out of 
alignment. Check to be sure the top of the doors are 
evenly aligned with each other. If necessary, the doors 
may be adjusted up or down to align.

• Add or subtract shims as shown to adjust the right 

door only. More shims are located under the hood on 
the left side in the bag with the filter bypass plug and 
mini manual.

To Raise Right Hand Door
• Lift the right hand door up so there is a gap below the 

bottom hinge bushing.

• Snap a shim onto the hinge pin below the bushing.
• Lower the door and re-check the alignment.
• Repeat as necessary.
To Lower Right Hand Door
• Lift the right hand door up so there is a gap below the 

bottom hinge bushing.

• Remove a shim by pushing shim off of the hinge pin.
• Lower the door and re-check the alignment.
• Repeat as necessary.

Shim

Bag location

 STEP 15  INSTALL TOEKICK

• Locate the supplied toekicks (shipped taped to the side 

of the refrigerator.

• The wider set of toe kicks will be used for flush 

installation. You can discard the other set of toe kicks.

• Attach the toekick assembly to the refrigerator using 

the supplied screws (2).

• A custom toekick can be installed to match or 

complement the surrounding cabinetry. Use the 
supplied toekick as a template to cut the shape.

IMPORTANT: A custom toekick can be installed to match 
or complement the surrounding cabinetry but can NOT 
cover the horizontal vent slots of the factory toe kick.

Содержание ZIP360NH





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды