monofil 4451 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 31

monofil 4451 Скачать руководство пользователя страница 8

- 8 -

03 SPECIAL SAFETY NOTES

3.1 Safety devices

Never manipulate the following:

- Safety locks
- Pressure releases
- Protection door
- all other safety devices

3.2 Special personal protective equipment

- Protective glasses

- Respiratory protection

- Protective gloves

- Observe the safety instructions of the operator

3.3 Special dangers at the machine - source of danger

3.4 Special dangers caused by the product

Source of danger

Instructed persons

Persons with technical training

Loose pipes (whipping)

Risk of injury due to whipping pipes

Initial operation made by specialist at the
manufacturer

Uncontrolled actuation of
the piston

Danger of crushing

Initial operation made by specialist at the
manufacturer

Machine falls down

Risk of personal injury

The machine must be mounted on a secure
and stable surface.

Spillage of liquids

Danger of slipping

Immediately remove and disposed of spilled
liquids in a professional manner.

Source of danger

Danger

Prevention

Symbol

Bursting can

Risk of personal injury

Check can for damage (e.g. deformation)
before filling.

Occuring vapours

Danger by poisoning/
suffocation

Wear respiratory protection

Source of Danger

Danger

Prevention

Symbol

«
...
6
7
8
9
10
...
»

Содержание 4451
































Отзывы:

Нет отзывов