Mondial Designs Limited HB095 2008, Руководство пользователя

Страница: 62 / 75

equipment details
98
equipment details
99
furnIture doorS
During normal travelling, vehicle vibration
and flexing may cause some of the furniture
doors to become out of alignment. For your
convenience many hinges are adjustable.
taBLe StoraGe
Tables stored in the table storage
compartment must be securely clipped into
place whilst in transit.
To avoid damage care must be taken when
removing tables from their stored position.
care of LamInate topS,
taBLeS, furnIture and doorS
DO NOT use abrasives, chemically treated
cloths or aggressive detergents as these may
cause damage.
DO NOT place hot objects on laminated
surfaces i.e. tops, tables. Any temperatures
70°C and over will cause permanent damage.
Clean worktop surfaces, furniture and door
fascias with a soft, slightly damp cloth, dry off
with a soft cloth.
SHower
When using the shower, always ensure that the
shower door is fully closed thus avoiding water
spray on unprotected areas.
omnIStep SLIde-out Step
operation
Press the “step out” key to bring the step out
until it reaches the end of its run or comes up
against an obstacle. The step does not come
out if the engine is running. Press the “step in”
key to take the step back until it reaches the
end of its run or comes up against an obstacle.
The step goes back in automatically when the
engine is running. In this situation the buzzer
sounds until the step is fully closed.
maintenance
Dirt and frost can prevent the step from
operating properly. In this case the rails and
moving parts should be cleaned or defrosted.
In case of electric break down
If the step does not retract by the motor
- Remove the front plate of the step. (Fig. 1)
- Remove the connection between the
footboard and the arms (with screwdriver
and wrench S10).
- Slide out the footboard.
- Reinstall the front plate.
Current drawn
- Working current: 5 A
- Blocking current, when fully extended or
retracted: 14 A
Fig. 1 Front plate
To close, reverse the operation and then check
if locked into position.
with crank: To open, rotate the crank until a
resistance is noticeable during the operation.
To close, reverse the operation and then check
if locked into position.
Seat SwIveL
(drIver/paSSenGer)
To turn the swivel, slide the BLACK lever rearwards
and adjust to the required angle. Before driving off
ensure the locking mechanism is fully secure.
BLInd and fLyScreen
The blind and flyscreen operate Independently
of each other and are engaged by connecting
to each other and sliding.
Safety precautions:
1. Repairs should be carried out only by
trained personnel.
2. Inform an approved dealer in case of
defects and malfunctions.
3. Before starting off, check the rooflight
for damage in the acrylic dome (tension
cracks) and the winding mechanism which
could arise owing to, for example, branches
and other natural causes.
4. Do not step in the acrylic dome.
5. Close the roof light before starting off
(check whether it is locked).
6. Do not leave the vehicle with the rooflight
open (danger of burglary or from rain).
7. Do not open in strong wind or rain.
8. Before opening, remove snow, ice, dirt, etc.
from the acrylic dome.
9. Malfunctions are to be repaired by an
approved dealer at once.
10. Do not use caustic detergents (danger of
tension cracks in the acrylic dome).
11. Do not operate whilst the vehicle is moving.
care instructions:
- Please clean the acrylic panes with the
Seitz Acrylic Cleaner.
- Stains and light scratches on the acrylic
pane can be removed by using the Seitz
Acrylic Polish and the Seitz special
polishing cloth.
- Use talcum powder (4 times yearly) to care
for the rubber seals
- Clean the blinds only with water and mild
soap suds
- The guarantee becomes null and void if
these instructions are not followed.