molex 63801-7200 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 36

molex 63801-7200 Скачать руководство пользователя страница 3

TM-3000 and TM-4000 Universal Press

Doc. No: TM-638017299

Release Date: 06-06-05

UNCONTROLLED COPY

Page 3 of 36

Revision: F

Revision Date: 11-27-18

Tooling Technical Assistance

Molex offers tooling technical assistance for customers who may need some guidance for tooling adjustments. This support

can be obtained by calling the number listed below and asking for the Molex Tooling Group.

This assistance is limited to the operation and setup of a customer’s Molex press. Questions with regard to Molex connector

products or how to identify the proper tooling or tooling documentation should be directed to your local Molex personnel or

customer service representative.

When calling for service on the press, a copy of the Tooling Manual and specific applicator Tooling Specification Sheet

should be present, and a person who is familiar with the applicator should be present. Be sure the following information is
supplied:

1.

Customer name

2.

Customer address

3.

Person to contact (e.g., name, title, e-mail, and telephone number)

4.

Applicator order number (Lease number, if applicable)

5.

Serial number (Lease number, if applicable)

6.

Molex Connector product order number

7.

Urgency of request

8.

Nature of problem

Application Tooling Support

Phone:

(402) 458-TOOL (8665)

E-Mail:

[email protected]

Website:

www.molex.com/applicationtooling

WARNING

WARNING

Never

use this press or wire processing machine

without guards or safety devices that are intended to
prevent hands from remaining in the die space.

Failure to observe this warning could result in severe
injury or death.

Do not use

compressed air to clean this equipment.

The forces created by compressed air can force debris
into the tool.

Failure to observe these precautions may result in injury
or property damage.

WARNING

Always

wear proper ear protection when operating or servicing this applicator.

CAUTION

Molex applicators are designed to operate in presses with standard shut heights of 135.80mm (5.346”).

Installation in crimp presses with other-than-standard shut heights can cause severe tool or applicator damage. It is advisable that before
installation, a check of the shut height be performed. Molex will not be liable for any damages as a result of installation in a crimp press with a

nonstandard or improperly set shut height.
Failure to observe these precautions may result in injury or property damage.

CAUTION

Never

perform any service or maintenance other than as described in this manual.

Never

modify, alter or misuse the equipment.

Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling.
Failure to observe this precaution may result in injury and property damage.

«
1
2
3
4
5
...
»

Содержание 63801-7200





































Отзывы:

Нет отзывов