Mohawk TR-33, Руководство пользователя

Страница: 24 / 87

MOHAWK MODEL TR-33/35/50/75/33WT/35WT/50WT/70WT
24
PRE OPERATION CHECK LIST
TRAINED OPERATOR
x
THE OPERATOR MUST BE FULLY TRAINED
AND QUALIFIED TO SAFELY AND
EFFECTIVELY OPERATE THIS EQUIPMENT OF
THIS SPECIFIC MAKE AND MODEL.
ABSENCE OF OBSTRUCTIONS
x
THE TOTAL WORK AREA MUST BE FREE OF
ANY AND ALL OBSTRUCTIONS AND BE
GENERALLY CLEAN. ( FREE OF OIL AND
DEBRIS )
VISUAL INSPECTION
x
THOROUGHLY INSPECT THE UNIT WITH A
TRAINED EYE, NOTING ANY PROBABLE
PROBLEM AREA. INSPECT THE FLOOR AND
THE ANCHORING FASTENERS AS WELL.
REPORT ANY QUESTIONABLE ITEMS.
NO LOAD PERFORMANCE CHECK
x
ALL MECHANICAL SAFETIES OPERATE
PROPERLY AND CONSISTENTLY.
x
NO EXTERNAL FLUID LEAKS.
x
NO BLEED DOWN.
x
EFFORTLESS AND SIMULTANEOUS
MOVEMENT.
x
LEVEL LIFTING.
x
CONTROLS FUNCTION PROPERLY.
x
ALL SAFETY MECHANISMS FULLY
FUNCTIONAL.
PREVIOUS DAY' S OPERATION REPORT
x
VERIFY WITH SUPERVISOR THAT THERE WERE
NO PROBLEMS EXPERIENCED DURING THE
PREVIOUS DAY'S USAGE. IF THERE WERE ANY
PROBLEMS, VERIFY THAT ALL NECESSARY
REPAIRS HAVE BEEN COMPLETED.
LIFTING PROCEDURES
PLACING VEHICLE ON LIFT
x
PERFORM PRE-OPERATION CHECK LIST ITEM
BY ITEM.
x
POSITION THE VEHICLE ONTO THE UNIT SO
THAT ALL TIRES ARE SECURELY ON THE
TRACKS. REFER TO “LIFTING IT RIGHT”
MANUAL AND ANSI/SAE J2184-OCT92 FOR
VEHICLE
LIFT POINTS AND PROPER
STANDARD LIFTING PRACTICES.
x
CENTER THE VEHICLE SO THAT THE WEIGHT
IS DISTRIBUTED EVENLY FORE AND AFT. THIS
CAN BE VERIFIED BY MONITORING THE
PRESSURE GAUGES ON THE CONTROL
CONSOLE PANEL. THE READINGS SHOULD BE
THE SAME OR WITHIN 300 P.S.I. THE LIFT MAY
NEED TO BE RAISED SLIGHTLY TO OBTAIN
THESE PRESSURE READING.
x
PLACE THE WHEEL CHOCKS IN A POSITION SO
THAT THE VEHICLE WILL BE SECURE ON THE
UNIT.
TO RAISE
x
TURN ON THE POWER UNIT.
x
SIMULTANEOUSLY PRESS & HOLD THE LOCK
RELEASE THEN THE UP BUTTON.
x
RAISE VEHICLE TO THE DESIRED WORKING
HEIGHT. RELEASE BUTTONS.
x
LOWER THE UNIT ONTO THE MECHANICAL
SAFETIES BY PRESSING THE DOWN SETTLE
BUTTON UNTIL THE GAUGES BOTH READ
APPROXIMATELY ZERO.
x
TURN OFF THE POWER UNIT
TO LOWER
x
INSPECT THE LIFTING AREA TO INSURE THAT
ALL PERSONNEL AND DEBRIS HAVE BEEN
CLEARED FROM THE LIFTING AREA.
x
TURN ON THE POWER UNIT.
x
SIMULTANEOUSLY PRESS & HOLD THE LOCK
RELEASE AND THE UP BUTTON.
x
RAISE UNIT APPROXIMATELY TWO INCHES.
RELEASE THE UP BUTTON ONLY, STILL
HOLDING THE LOCK RELEASE BUTTON AND
THEN PRESS THE DOWN BUTTON.
x
CONTINUE TO HOLD THE BUTTONS UNTIL THE
TRACKS ARE AT THE DESIRED HEIGHT OR ARE
FULLY LOWERED AND DOWNWARD MOTION
HAS HALTED.
x
IF LOWERING ONTO MECHANICAL SAFETIES,
RELEASE BOTH BUTTONS, THEN PRESS THE
DOWN SETTLE BUTTON UNTIL THE GAUGES
BOTH READ APPROXIMATELY ZERO.
x
IF LOWERING TO THE FLOOR, LOWER FULLY
UNTIL UNIT STOPS, RELEASE DOWN BUTTON
ONLY, AND WHILE MAINTAINING LOCK
RELEASE BUTTON, PRESS THE DOWN SETTLE
BUTTON UNTIL THE GAUGES BOTH READ
APPROXIMATELY ZERO.
x
TURN OFF THE POWER UNIT
NOTE:
IF FOR ANY REASON, THE LIFT BECOMES INOPERATIVE
IN THE RAISED POSITION WITH A VEHICLE ON IT, CONTACT.
OUR LOCAL MOHAWK REPRESENTATIVE OR THE MOHAWK
FACTORY.