Mohawk LMF-12 страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 76

background image

MOHAWK MODEL LMF-12, TP-15,TP-16 & TP-18

16

TROUBLE SHOOTING, CONTINUED

POSSIBLE CAUSE

SOLUTION

RAISING UNEVEN, CONTINUED

SHOP FLOOR UNEVEN

USE SPECIAL LIFT PADS.

SEE FIGURE 10.

DIVERTER VALVE

REMOVE BLEED LINE FROM THE TOP OF THE OFF SIDE CYLINDER AND CAP
USING MOHAWK PART # 601-420-001. IF THE UNIT CONTINUES TO DRIFT DOWN
THE DIVERTER PULL VALVE WILL NEED TO BE CLEANED OR REPLACED.

OFF SIDE CYLINDER

REMOVE BLEED LINE FROM THE TOP OF THE OFF SIDE CYLINDER AND CAP
USING MOHAWK PART # 601-420-001. IF THE UNIT NO LONGER DRIFTS DOWN
THE OFF SIDE CYLINDER WILL NEED TO BE SERVICED..

MAIN SIDE CYLINDER

PERFORM HYDRAULIC SAFETY CHECKS. CHECK FOR INTERNAL HYDRAULIC
LEAKS

SLOW DRIFT DOWN

SAFETIES NOT ENGAGED

RAISE UNIT TO RE-ENGAGE SAFETIES. THEN LOWER UNIT ONTO SAFETIES.

POWER UNIT LOWERING VALVE
CONTAMINATION

BACK FLUSH POWER UNIT: PULL DOWN ON THE LOWERING HANDLE, AND
THEN ENGAGE THE UP BUTTON AT THE SAME TIME. RUN UNIT APPROX. 10
SECONDS

DIVERTER VALVE

REMOVE BLEED LINE FROM THE TOP OF THE OFF SIDE CYLINDER AND CAP
USING MOHAWK PART # 601-420-001. IF THE UNIT CONTINUES TO DRIFT DOWN
THE DIVERTER PULL VALVE WILL NEED TO BE CLEANED OR REPLACED.

OFF SIDE CYLINDER

REMOVE BLEED LINE FROM THE TOP OF THE OFF SIDE CYLINDER AND CAP
USING MOHAWK PART # 601-420-001. IF THE UNIT NO LONGER DRIFTS DOWN
THE OFF SIDE CYLINDER WILL NEED TO BE SERVICED..

EXTERNAL HYDRAULIC LEAKS

NOTE: TIGHTEN ALL FITTINGS PER SPECIFICATIONS

MAIN SIDE CYLINDER

THOROUGHLY CLEAN THE CYLINDER. VERIFY LEAK ORIGIN. FITTINGS ARE
TO BE TIGHTENED PER SPECIFICATIONS

OFF SIDE CYLINDER

THOROUGHLY CLEAN THE CYLINDER. VERIFY LEAK ORIGIN. FITTINGS ARE
TO BE TIGHTENED PER SPECIFICATIONS.

BAD FLAIR OR FITTING

REMOVE THE HYDRAULIC LINE AND INSPECT FLAIR AND FITTING FOR
DEFORMATION. REPLACE IF NEEDED.

BAD O-RING (O-RING TYPE FITTINGS)

CHANGE O-RING

LOOSE PIPE FITTING

REMOVE, RESEAL, AND RE-INSTALL FITTING.
SEAL ALL PIPE FITTING CONNECTIONS WITH THREAD SEALANT MOHAWK
PART # 601-610-002 NOTE

: DO NOT USE TEFLON TAPE.

«
...
21
22
23
24
25
...
»

Содержание LMF-12













































































Отзывы:

Нет отзывов

Похожие инструкции для LMF-12

Бренд: bester Страницы: 68

Бренд: VENCO Страницы: 31

DESKLINE DL15 IC

Бренд: Linak Страницы: 33

Heat Control System

Бренд: ORTAL Страницы: 20

Бренд: Purelogic Страницы: 60

Бренд: Thermal Dynamics Страницы: 40

Multi-process 200

Бренд: Tokentools Страницы: 29

Бренд: Tweco Страницы: 64

Бренд: Forney Страницы: 32

Бренд: Denyo Страницы: 30

EVO SPEED STAR 380 TC

Бренд: Cebora Страницы: 212

Plasma 40 Torch

Бренд: BOC Страницы: 12

Бренд: Nussbaum Страницы: 72

Бренд: Air Liquide Страницы: 52

Бренд: Hitbox Страницы: 18

Бренд: Lincoln Electric Страницы: 32

Бренд: Jefferson Страницы: 20

Devicenet R7F4DD-DA16B-C

Бренд: M-system Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды