manualshive.com logo in svg

Mohawk LMF-12, Руководство пользователя

Поделиться
Скачать
Mohawk LMF-12 Скачать руководство пользователя страница 16

MOHAWK MODEL LMF-12, TP-15,TP-16 & TP-18 

 

9

 
 

SAFETY TIPS 

 

 

PLEASE POST THE 

AUTOMOTIVE LIFT SAFETY

 

TIPS

 

CARD, 

(A COPY IS INCLUDED 

IN THE PARTS BOX) 

WHERE THEY WILL BE CONSTANTLY REMINDED TO YOUR LIFT 

OPERATOR. FOR INFORMATION SPECIFIC TO THE LIFT, ALWAYS REFER TO THE MOHAWK 
MANUAL. 
 
 
 

•

 

INSPECT YOUR LIFT DAILY. NEVER OPERATE IT 
IF IT MALFUNCTIONS OR IF IT HAS BROKEN OR 
DAMAGED PARTS. REPAIRS SHOULD BE MADE 
WITH ORIGINAL MOHAWK PARTS. 

 

•

 

OPERATING CONTROLS ARE DESIGNED TO 
CLOSE WHEN RELEASED. DO NOT BLOCK OPEN 
OR OVERRIDE THEM. 

 

•

 

NEVER OVERLOAD YOUR LIFT BEYOND 
STATED LIFTING CAPACITY. RATED CAPACITY 
IS SHOWN ON NAMEPLATE AFFIXED TO THE 
LIFT. 

 

•

 

ONLY TRAINED AND AUTHORIZED PERSONNEL 
SHOULD DO POSITIONING OF VEHICLE AND 
OPERATION OF THE LIFT. 

 

•

 

DO NOT ALLOW CUSTOMERS OR BY- STANDERS 
TO OPERATE THE LIFT OR TO BE IN A LIFTING 
AREA DURING ITS OPERATION. ONLY 
PROPERLY TRAINED PERSONNEL SHOULD BE 
ALLOWED TO OPERATE LIFT. 

 

•

 

NEVER RAISE A VEHICLE WITH PERSONS 
INSIDE.  

 

•

 ALWAYS KEEP LIFT AREA FREE OF 

OBSTRUCTIONS, DEBRIS, GREASE, AND OIL. 

 

•

  PERFORM THE PRE-OPERATION CHECK LIST, 

PER INSTRUCTIONS, BEFORE RAISING VEHICLE 
TO DESIRED HEIGHT. 

 

•

 

BEFORE DRIVING VEHICLE INTO THE BAY, 
POSITION ARMS AND SUPPORTS TO PROVIDE 

UNOBSTRUCTED CLEARANCE. DO NOT HIT OR 
RUN OVER LIFT ARMS, ADAPTERS, OR AXLE 
SUPPORTS. THIS COULD DAMAGE LIFT OR 
VEHICLE. 

 

•

 

LOAD VEHICLE ON LIFT CAREFULLY. POSITION 
LIFT SUPPORTS TO CONTACT AT THE VEHICLE 
MANUFACTURER’S RECOMMENDED LIFTING 
POINTS. RAISE LIFT UNTIL SUPPORTS CONTACT 
VEHICLE. CHECK SUPPORTS FOR SECURE 
CONTACT WITH VEHICLE. RAISE LIFT TO 
DESIRED WORKING HEIGHT. 

CAUTION: 

IF 

YOU ARE WORKING UNDER VEHICLE, LIFT 
SHOULD BE RAISED HIGH ENOUGH FOR 
LOCKING DEVICE TO BE ENGAGED. 

 

•

 

NOTE THAT WITH SOME VEHICLES, THE 
REMOVAL OR INSTALLATION OF COMPONENTS 
MAY CAUSE A CRITICAL SHIFT IN THE CENTER 
OF GRAVITY, AND RESULT IN RAISED VEHICLE 
INSTABILITY. REFER TO THE VEHICLE 
MANUFACTURER’S SERVICE MANUAL FOR 
RECOMMENDED PROCEDURES WHEN VEHICLE 
COMPONENTS ARE REMOVED. 

 

•

 

BEFORE LOWERING LIFT, BE SURE TOOL 
TRAY’S, STANDS, ETC. ARE REMOVED FROM 
UNDER VEHICLE. RELEASE LOCKING DEVICES 
BEFORE ATTEMPTING TO LOWER LIFT. 

 

•

  BEFORE REMOVING VEHICLE FROM THE LIFT 

AREA, POSITION LIFT ARMS AND SUPPORTS TO 
PROVIDE AN UNOBSTRUCTED EXIT. 

 

 

Содержание LMF-12













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды