manualshive.com logo in svg

Mohawk LMF-12, Руководство пользователя

Поделиться
Скачать
Mohawk LMF-12 Скачать руководство пользователя страница 15

MOHAWK MODEL LMF-12, TP-15,TP-16 & TP-18 

 

8

 
 
 

INSTALLATION INSTRUCTIONS, CONT. 

 

 

BLEEDING PROCEDURE 

 

ENGAGE THE UP BUTTON ON THE POWER UNIT. OBSERVE THE 
CARRIAGE. WHEN THE MAIN AND OFF SIDE CARRIAGES HAVE 
REACHED FULL HEIGHT, CONTINUE TO RUN THE UNIT FOR 10 
SECONDS.  
 
RELEASE THE UP BUTTON AND WAIT ONE MINUTE, THEN HOLD 
THE UP BUTTON AGAIN FOR 10 SECONDS. REPEAT THIS 
PROCEDURE THREE TIMES (THIS WILL PURGE THE AIR FROM 
THE HYDRAULIC SYSTEM) 
 

NOTE

 

 

•

 

LISTEN FOR THE PRESSURE RELIEF VALVE. A NOTICEABLE 
INCREASE IN POWER UNIT VOLUME  THIS MAY INDICATE 
THAT THE NUTS ON THE LIFTING RODS NEED TO BE 
ADJUSTED. ADJUST THE NUTS EVENLY ON BOTH SIDES OF 
THE CARRIAGE TO ALLOW THE CYLINDERS TO FULLY 
STOKE AT THE TOP.  

 
ASSEMBLE THE TWO HEIGHT ADAPTERS BRACKETS TO THE 
BACK OF THE MAIN AND OFF SIDE POST USING THE FOUR 5/16 
BOLT, WASHER & NYLON LOCK NUTS. 

REFER TO MAN505

 

 
PLACE THE FOUR 5 INCH., 7 ½ INCH AND 10 INCH HEIGHT 
ADAPTERS INTO PLACE INTO THE HEIGHT ADAPTER BRACKETS. 
 

SHIMMING THE POST 

 

LEVEL THE POST BY INSERTING THE SUPPLIED SHIMS UNDER 
THE POST FOOTING AROUND THE WEJ-IT ANCHOR. THE LIFT 
MUST BE LEVEL BOTH FRONT TO REAR AND SIDE TO SIDE. A 
LEVELING DEVICE AND A MEASURING TAPE MUST BE USED. 

REFER TO FIGURES 5 & 6

. 

 

•

 

LEVEL THE MAIN SIDE POST FRONT TO REAR AND SIDE-TO-
SIDE USING A BUBBLE LEVEL.  

 

•

 

LEVEL THE OFF SIDE POST FRONT TO REAR USING A 
BUBBLE LEVEL.  SET THE POST PARALLEL TO THE MAIN 
SIDE POST USING A MEASURING TAPE, MEASURING FROM 
THE EDGE OF THE MAIN SIDE CHANNEL TO THE EDGE OF 
THE OFF SIDE CHANNEL AT THE BASE AND AT THE TOP OF 
THE POST. 

 

•

 

THE MEASUREMENT AT THE TOP OF THE POST MUST BE 
THE SAME AS THE MEASUREMENT AT THE BASE OF THE 
POST. 

 
AT THIS TIME PERFORM THE PRE-OPERATION CHECK LIST AND 
MAINTENANCE PROCEDURES (DAILY - WEEKLY - MONTHLY) 
MAKE ALL ADJUSTMENTS PERTAINING TO THESE PROCEDURES. 

 
 

DIVERTER VALVE OPERATION 

 

WARNING

 

 

AS WITH ALL FUNCTIONS OF THE LIFT UNIT, NEVER OPERATE 
THE DIVERTER VALVE UNLESS YOU HAVE FIRST PERFORMED 
THIS OPERATION WITH NO VEHICLE, AND FULLY UNDERSTAND 
ITS FUNCTIONS.  
 
BOTH MECHANICAL SAFETIES MUST BE ENGAGED BEFORE 
OPERATING THE DIVERTER VALVE. 

 

PURPOSE 

 

•

 

THE PURPOSE OF THE DIVERTER VALVE IS TO ENABLE THE 
OPERATOR TO RAISE OR LOWER THE OFF SIDE CARRIAGE 
INDEPENDENTLY OF THE MAIN SIDE CARRIAGE. 

 

TO OPERATE THE DIVERTER VALVE 

 
 
ENGAGE THE DIVERTER VALVE BY PULLING DOWN ON THE 
DIVERTER VALVE PULL KNOB. 

REFER TO MAN504

 

 

•

 

THIS WILL DIVERT ALL FUNCTIONS OF THE POWER UNIT TO 
THE OFF SIDE CYLINDER. 

 
WITH THE VALVE ENGAGED, ENERGIZE THE POWER UNIT BY 
PUSHING THE UP BUTTON.  
 
WHEN THE DESIRED HEIGHT HAS BEEN ACHIEVED, RELEASE 
THE DIVERTER VALVE PULL KNOB AND THE UP BUTTON. 
 
PULLING DOWN ON THE LOWERING HANDLE, LOWER THE UNIT 
ONTO BOTH MECHANICAL SAFETIES ENDING THIS PROCEDURE. 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание LMF-12













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды