Mitsubishi TDJ300D Скачать руководство пользователя страница 18

Страница: 18 / 91

– 14 –

Specification

How to determine defective or not defective.

When the battery voltage is applied between the lead

and the ground wire of the main body, the

compressor will turn if the pulley and the friction plate

stick together (it clinks).

If it will not turn even when voltage is applied, it is

defective. Measure by a tester the continuity between

the lead

and a ground of the main body, and it is

normal if there is continuity and defective if no

continuity due to disconnection of the coil. When

sound is heard, it is defective due to wear of the

bearing. If the magnet clutch is defective, replace its

assembly.

Measuring of air-gap

TDJ300D: 0.3 ~ 0.5mm

TDJ430D: 0.3 ~ 0.6mm

10.3 Heat accumulator

While separating liquid refrigerant from gas refrigerant

so as not to let the compressor sucks the liquid

refrigerant, increase capacity of refrigeration by

making a heat-exchange of high temperature liquid

refrigerant and low temperature gas refrigerant.

10.4 Accumulator (type 2 only)

Separate liquid refrigerant from gas refrigerant so as

not to let the compressor sucks the liquid refrigerant.

Here, the refrigerant is designed to flow from U type

tube only to the engine side or motor pack side where

the compressor is in operation.

Volume

Direction of revolving

Belt used

TDJ300D

TDJ430D

53W

31W

Right

Type B

one each

Heat accumulator

Accumulator

Magnet clutch

Содержание TDJ300D




























































































Результаты поиска

Содержание TDJ300D

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi TDJ300D, Руководство по обслуживанию

Результаты поиска

Содержание TDJ300D

Отзывы:

Бренды по названию

Популярные бренды