Mitsubishi PAJERO IV Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 72

background image

BEFORE ROAD TEST

PRE-DELIVERY INSPECTION

1-12

20. INSTRUMENT PANEL CONTROLS

M6010700400083

Check the operation of the following
1. Horn
2. Headlamps
3. Exterior and interior lamps
4. Instrument panel lamps
5. Instrument brightness control

21. METERS, GAUGES, WARNING
LAMPS AND INDICATION LAMPS

M6010700500024

1. Check the meters and gauges are functioning

properly.

2. Check each indicator lamp and warning lamp

functions properly.

22. AIR CONDITIONER, HEATER AND
DEFROSTER SYSTEM

M6010700600021

Check the systems for proper operation.

1. Air conditioner

(1) Operate the air conditioner system.
(2) Operate the air conditioner light.
(3) Operate the control lever in all ranges.
(4) Operate the blower motor switch in all ranges.

2. Heater and defroster

(1) After the engine has warmed up, turn on the

heater.

(2) Operate the blower motor switch in all ranges.
(3) Move the control to "Defrost" position.

A: From front and side defroster
B: From centre ventilators
C: From side ventilators
D: From under the instrument panel
E: From under the front seat (some models only)

23. WIPERS AND WASHERS

M6010700700028

1. Front wiper and washer

(1) Check operation of the front wipers in all

ranges.

(2) Check the aim of the front washer stream.
(3) Check the wiper blade-stop positions.
(4) Verify that the interval between cycles of

wiping is shifted when timer knob is turned to
any position.

(5) Verify that the front wipers function by

operating the washer switch.

2. Rear wiper and washer

(1) Check the operation of the rear wiper.
(2) Check the aim of the rear washer stream.
(3) Check the wiper blade-stop positions.

AC305624

AC305625

AC305626

AC305627

«
...
16
17
18
19
20
...
»

Содержание PAJERO IV









































































Отзывы:

Нет отзывов

Похожие инструкции для PAJERO IV

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 2

Бренд: Cadillac Страницы: 494

Бренд: Cadillac Страницы: 500

Бренд: Cadillac Страницы: 40

Бренд: Cadillac Страницы: 432

Бренд: Cadillac Страницы: 338

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 438

PRIME DESIGN VRI3-E-PM11

Бренд: Safe Fleet Страницы: 12

DAF POWERCHOICE 250A

Бренд: Paccar Страницы: 20

Бренд: Mercedes-Benz Страницы: 30

Бренд: CITROEN Страницы: 52

Бренд: Velleman Страницы: 6

Бренд: A-Tach Страницы: 2

Бренд: Volvo Страницы: 266

Бренд: Yakima Страницы: 12

Бренд: FALCON RIDGE Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды