Mitsubishi PAJERO IV Скачать руководство пользователя страница 34

Страница: 34 / 72

OPERATIONS INSIDE THE ENGINE COMPARTMENT

PERIODIC INSPECTION AND MAINTENANCE

2-10

A5. CHECK OPERATION OF
CRANKCASE EMISSION CONTROL
SYSTEM

M6020200700347

BREATHER HOSE

1. Inspect the breather hose for cracks or damage.
2. Clean the inside of the breather hose if neces-

sary.

3. Inspect the ventilation filter for clogging.

VENTILATION HOSE

1. Check entire circumference and length of hoses

using a mirror as required.

2. Check all clamps for tightness and the connec-

tions for leakage.

3. Hoses should be replaced immediately if there is

any evidence of deterioration or damage.

POSITIVE CRANKCASE VENTILATION
SYSTEM CHECK

1. Remove the ventilation hose from the PCV

(Positive crankcase ventilation) valve.

2. Remove the PCV valve from the rocker cover.
3. Reinstall the PCV valve at the ventilation hose.
4. Start the engine and run at idle.

5. Place finger at the opening of the PCV valve and

check that vacuum of the intake manifold is felt.

NOTE: At this moment, the plunger in the PCV
valve moves back and forth.

6. If vacuum is not felt, clean the PCV valve or

replace it.

7. Apply a small amount of new engine oil to the

O-ring on the PCV valve, and tighten to the
specified torque. <6G75>

Tightening torque: 2.5

0.4 N

⋅

AC610025

Breather hose

AC610047

Ventilation hose

PCV valve

AC305653AD

PCV valve

<6G72>

AC609736AC

<6G75>

PCV valve

Содержание PAJERO IV









































































Результаты поиска

Содержание PAJERO IV

Отзывы:

Похожие инструкции для PAJERO IV

Бренды по названию

Популярные бренды

Mitsubishi PAJERO IV, Руководство по обслуживанию

Результаты поиска

Содержание PAJERO IV

Отзывы:

Похожие инструкции для PAJERO IV

Бренды по названию

Популярные бренды