manualshive.com logo in svg

Mitsubishi MFZ-KA-VA, Руководство по техническому обслуживанию, Страница: 57 / 74

Поделиться
Скачать
Mitsubishi MFZ-KA-VA Скачать руководство пользователя страница 57

57

 

Set the air outlet selection switch to

 

.

 

Set the air outlet selection switch to 

.

Air blows out automatically from the upper and lower air out-
lets as shown in the table below.

COOL

DRY

HEAT

Operation

Air

flow

Conditions

Upper and lower air flow

Room temperature
and set temperature
are different.

Upper air flow

Room temperature is
close to set tempera-
ture, or the air
conditioner has
operated for 1 hour.

Upper air flow only Upper and lower air flow

Air flow temperature
is high.

Upper air flow

Air flow temperature
is low.
(During defrosting
operation, start of
operation, etc.)

NOTE 2 : Set the air outlet selection switch to the end correctly. Otherwise, air outlet cannot be selected as intended. 

Description of operation

• Be sure to keep the area around the damper of the lower air outlet free of any objects. If any objects block the normal
  operation of the damper, the left operation indicator lamp may blink.

With this function, air comes out simultaneously from the upper and lower air outlets so that the room
can be cooled or heated effectively. This function is set using the switch behind the front grille of the
indoor unit. (This function is available in cooling and heating operation.)

1.How to set to blow out air from the upper
   and lower air outlets:

2.How to set to blow out air from the upper 
   air outlet only:

NOTE 1 : Be sure to turn off the air conditioner before changing the switch setting. 

• As for indoor fan motor (upper), refer to "Indoor fan speed control (3-1.2, 3-2.2, 3-3.2)" and 
  "INDOOR FAN MOTOR CONTROL (3-5.)".

The direction (opening and closing of the damper) and the volume of the airflow from the lower air 
outlet are controlled automatically.

2

:

7

:

Indoor fan motor (Lower) in COOL OPERATION

Damper

OPEN

CLOSE

35

:

40

:

Indoor fan motor (Lower) in HEAT OPERATION

Indoor coil thermistor temperature

Damper

OPEN

CLOSE

Difference between 
room temperature and 
set temperature 
during operation

Indoor coil thermistor 
temperature

Difference between room temperature and 
set temperature during operation

(9) Damper operation

OBT14A--2qxp  06.1.12 1:09 PM  Page 57

Downloaded from AC-Manual.com Manuals

Содержание MFZ-KA-VA











































































Отзывы:

Нет отзывов