Mitsubishi MFZ-KA-VA Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 74

Mitsubishi MFZ-KA-VA Скачать руководство пользователя страница 22

22

MSZ-GA MICROPROCESSOR CONTROL

2

Once the operation mode is set, the same operation mode can be repeated by simply turning OPERATE/STOP
(ON/OFF) button ON.
Indoor unit receives the signal with a beep tone.
When the system turns off, 3-minute time delay will operate to protect system from overload and compressor will not
restart for 3 minutes.

WIRELESS REMOTE CONTROLLER

ON-TIMER button

CLOCK SET button

TIME SET buttons
FORWARD button
BACKWARD button

OFF-TIMER button

(This diagram shows an overall view.)

RESET button

VANE CONTROL button

Signal transmitting section

Operation display section

Temperature buttons

OPERATE/STOP
(ON/OFF) button

FAN SPEED CONTROL button

OPERATION SELECT button

ECONO COOL button

Indication of
remote controller
model is on back

MSZ-GA22VA
MSZ-GA25VA MUZ-GA25VA
MSZ-GA35VA MUZ-GA35VA

Operation Indicator lamp
The operation indicator at the right side of the indoor unit indicates the operation state.

Approximate
2

:

or more

Difference
between target
temperature
and room
temperature

Approximate
2

:

or less

This shows that the
air conditioner is
operating to reach
the target temperature.
Please wait until the
target temperature is
obtained.

This shows that the
room temperature is
approaching the
target temperature.

Operation state

Indication

Lighted

Not lighted

•The following indication applies regardless of shape of the indicator.

Operation Indicator

INDOOR UNIT DISPLAY SECTION

OBT14A--1qxp 06.1.12 1:07 PM Page 22

Downloaded from AC-Manual.com Manuals

«
...
20
21
22
23
24
...
»

Содержание MFZ-KA-VA











































































Отзывы:

Нет отзывов